prEN 15599-1

Thermal insulation products for building equipment and industrial installations - In-situ thermal insulation formed from expanded perlite (EP) products - Part 1: Specification for bonded and loose-fill products before installation

prEN 15599-1

Name:prEN 15599-1   Standard name:Thermal insulation products for building equipment and industrial installations - In-situ thermal insulation formed from expanded perlite (EP) products - Part 1: Specification for bonded and loose-fill products before installation
Standard number:prEN 15599-1   language:English language
Release Date:   technical committee:CEN/TC 88 - Thermal insulating materials and products
Drafting committee:CEN/TC 88 - Thermal insulating materials and products   ICS number:91.100.60 - Thermal and sound insulating materials
SLOVENSKI STANDARD
oSIST prEN 15599-1:2007
01-januar-2007
Toplotnoizolacijski proizvodi za opremo stavb in industrijske inštalacije -
Proizvodi iz ekspandiranega perlita (EP), oblikovani na mestu vgradnje - 1. del:
Specifikacija za vezane in razsute proizvode pred vgradnjo
Thermal insulation products for building equipment and industrial installations - In-situ
thermal insulation formed from expanded perlite (EP) products - Part 1: Specification for
bonded and loose-fill products before installation
Wärmedämmstoffe für die Haustechnik und für betriebstechnische Anlagen - An der
Verwendungsstelle hergestellte Wärmedämmung mit Produkten aus expandiertem
Perlite (EP) - Teil 1: Spezifikation für gebundene und Schüttprodukte vor dem Einbau
Produits isolants thermiques pour l'isolation du bâtiment et les installations industrielles -
Isolation thermique formée en place a base de granulats légers de Perlite expansée (EP)
- Partie 1: Spécification de produits liés et en vrac avant mise en oeuvre
Ta slovenski standard je istoveten z: prEN 15599-1
ICS:
91.100.60 0DWHULDOL]DWRSORWQRLQ Thermal and sound insulating
]YRþQRL]RODFLMR materials
oSIST prEN 15599-1:2007 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 15599-1:2007

---------------------- Page: 2 ----------------------
oSIST prEN 15599-1:2007
EUROPEAN STANDARD
DRAFT
prEN 15599-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2006
ICS 91.100.60

English Version
Thermal insulation products for building equipment and industrial
installations - In-situ thermal insulation formed from expanded
perlite (EP) products - Part 1: Specification for bonded and
loose-fill products before installation
Produits isolants thermiques pour l'isolation du bâtiment et Wärmedämmstoffe für die Haustechnik und für
les installations industrielles - Isolation thermique formée betriebstechnische Anlagen - An der Verwendungsstelle
en place à base de granulats légers de Perlite expansée hergestellte Wärmedämmung mit Produkten aus
(EP) - Partie 1: Spécification de produits liés et en vrac expandiertem Perlite (EP) - Teil 1: Spezifikation für
avant mise en oeuvre gebundene und Schüttprodukte vor dem Einbau
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 88.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 15599-1:2006: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 15599-1:2007
prEN 15599-1:2006 (E)
Contents Page
Foreword. 4
1 Scope. 5
2 Normative references . 5
3 Terms, definitions, symbols, units and abbreviated terms . 6
3.1 Terms and definitions. 6
3.1.1 Terms and definitions as given in prEN ISO 9229 . 6
3.1.2 Additional terms and definitions . 6
3.2 Symbols, units and abbreviated terms. 7
4 Requirements . 7
4.1 General. 7
4.2 For all applications . 7
4.2.1 Thermal conductivity. 7
4.2.2 Loose bulk density. 8
4.2.3 Particle size . 8
4.2.4 Reaction to fire . 8
4.2.5 Durability characteristics . 8
4.3 For specific applications. 9
4.3.1 General. 9
4.3.2 Maximum service temperature . 9
4.3.3 Minimum service temperature . 9
4.3.4 Crushing resistance. 9
4.3.5 Water vapour transmission. 9
4.3.6 Trace quantities of water soluble ions and pH-value. 9
4.3.7 Release of dangerous substances. 9
5 Test methods. 10
5.1 Sampling . 10
5.2 Conditioning . 10
5.3 Testing. 10
5.3.1 General. 10
5.3.2 Thermal conductivity. 10
6 Designation code . 11
7 Evaluation of conformity. 11
8 Marking and labelling . 12
Annex A (normative) Factory production control. 13
Annex B (normative) Preparation of the test specimens to measure thermal conductivity. 14
B.1 Products EPA, and EPC used as loose fill insulation. 14
B.2 Product EPM used as bonded insulation, also products EPA and EPC when used
as site mixed bonded insulation . 14
Annex C (normative) Special conditions to be used for the determination of organic
content . 15
C.1 Principle . 15
C.2 Apparatus . 15
C.3 Procedure . 15
C.4 Calculation and expression of results. 15
C.5 Test report . 15
Annex D (normative) Determination of maximum service temperature. 16
2

---------------------- Page: 4 ----------------------
oSIST prEN 15599-1:2007
prEN 15599-1:2006 (E)
D.1 Principle . 16
D.2 Apparatus . 16
D.3 Procedure . 16
D.4 Test report . 16
Annex ZA (informative) Clauses of this European Standard addressing the provisions of
the EU Construction Products Directive .17
ZA.1 Scope and relevant characteristics. 17
ZA.2 Procedures for attestation of conformity of loose-fill expanded perlite products. 18
ZA.2.1 Systems of attestation of conformity. 18
ZA.2.2 EC declaration of conformity. 20
ZA.3 CE Marking and labelling . 20

3

---------------------- Page: 5 ----------------------
oSIST prEN 15599-1:2007
prEN 15599-1:2006 (E)
Foreword
This document (prEN 15599-1:2006) has been prepared by Technical Committee CEN/TC 88
“Thermal insulating materials and products”, the secretariat of which is held by DIN.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under a mandate given to CEN by the European Commission and
the European Free Trade Association, and supports essential requirements of EU Directive.
For relationship with EU Directive, see informative Annex ZA, which is an integral part of this
document.
This standard consists of two parts. The first part, which is the harmonised part satisfying the mandate,
the CPD and is the basis for the CE marking, covers the products, which are placed on the market.
The second part, which is the non-harmonised part, covers the specification for the installed products.
This document contains five annexes:
Annex A  (informative) - Factory production control
Annex B  (normative) - Preparation of test specimens to measure thermal conductivity
Annex C (normative) - Special conditions to be used for the determination of organic
content
Annex D  (normative) - Determination of maximum service temperature
Annex ZA (informative) - Clauses of this European Standard addressing the provisions of
the EU Construction Products Directive
This European Standard is one of a series for urea formaldehyde foam, loose-fill cellulose products,
expanded perlite and exfoliated vermiculite in-situ formed insulation products used in building
equipment and industrial installations, but this standard may be used in other areas where appropriate.
EN 14316-1 covers the use of expanded perlite in buildings.
4

---------------------- Page: 6 ----------------------
oSIST prEN 15599-1:2007
prEN 15599-1:2006 (E)
1 Scope
This European Standard specifies the requirements for expanded perlite products which are used for
the thermal insulation of building equipment and industrial installations with an operating temperature
in the range of approximately 0 ºC to +650 ºC.
NOTE Expanded perlite products can be used below 0 °C. The manufacturer’s advice should be obtained
regarding the suitability of the product in the intended application below 0 °C.
This European Standard specifies the requirements for the three types of expanded perlite products
Perlite Aggregate (EPA), Coated Perlite (EPC) and Premixed Perlite (EPM), containing less than 1 %
organic material as defined by annex C.
This Part 1 of this standard is a specification for the insulation products before installation.
This Part 1 of this standard describes the product characteristics and includes procedures for testing,
evaluation of conformity, marking and labelling.
This European Standard does not specify the required level of a given property to be achieved by a
product to demonstrate fitness for purpose in a particular application. The levels required for a given
application are to be found in regulations or non-conflicting standards.
This European Standard does not cover factory made insulation products of formed shapes and
boards made with expanded perlite, and does not cover products intended to be used for the
insulation of buildings.
This European Standard does not specify performance requirements for airborne sound insulation
and for acoustic absorption applications.
2 Normative references
This European Standard incorporates by dated or undated reference provisions from other
publications. These normative references are cited at the appropriate place in the text and the
publications are listed hereafter. For dated references subsequent amendments to or revisions of any
of the publications apply to this European Standard only when incorporated in it by amendment or
revision. For undated references the latest edition of the publication referred to applies.
EN 932-1, Tests for general properties of aggregates — Part 1: Methods for sampling.
EN 932-2, Tests for general properties of aggregates — Part 2: Methods for reducing laboratory samples.
EN 933-1, Tests for geometrical properties of aggregates — Part 1: Determination of particle size
distribution — Sieving method.
EN 993-14, Methods of test for dense shaped refractory products. Determination of thermal
conductivity by the hot-wire (cross-array) method.
EN 1097-3, Tests for mechanical and physical properties of aggregates — Part 3: Determination of
loose bulk density and voids.
EN 12667, Determination of thermal resistance by means of guarded hot plate and heat flow meter
methods — Products of high and medium thermal resistance.
EN 13055-1, Lightweight aggregates for concrete, mortar and grout
5

---------------------- Page: 7 ----------------------
oSIST prEN 15599-1:2007
prEN 15599-1:2006 (E)
EN 13055-2, Lightweight aggregates for bituminous mixtures and surface treatments and for unbound
and bound applications excluding concrete, mortar and grout.
EN 13172, Thermal insulating products — Evaluation of conformity.
EN 13468, Thermal insulating products for building equipment and industrial installations.
Determination of trace quantities of water soluble chloride, fluoride, silicate, sodium ions and pH.
EN 13820, Thermal insulating materials for building applications — Determination of organic content.
prEN 14706, Thermal insulating products for building equipment and industrial installations.
Determination of maximum service temperature.
prEN ISO 9229, Thermal insulation — Definitions of terms.
EN ISO 13787, Thermal insulation products for building equipment and industrial installations -
Determination of declared thermal conductivity.
3 Terms, definitions, symbols, units and abbreviated terms
3.1 Terms and definitions
For the purpose of this standard, the following terms and definitions apply.
3.1.1 Terms and definitions as given in prEN ISO 9229
3.1.1.1
expanded perlite
lightweight granular (insulation) material manufactured from naturally occurring volcanic rock
expanded by heat to form a cellular structure
3.1.2 Additional terms and definitions
3.1.2.1
perlite aggregate
expanded perlite with no treatment or surface coating, used as a loose insulation in cavities
3.1.2.2
coated perlite
expanded perlite which has a coating
3.1.2.3
premixed perlite
expanded perlite premixed with binders
3.1.2.4
level
the given value which is the upper or lower limit of requirement, where the level is given by the
declared value of the characteristic concerned
3.1.2.5
class
a combination of two levels of the same property between which the performance shall fall, where the
level is given by the declared value of the characteristic concerned
6

---------------------- Page: 8 ----------------------
oSIST prEN 15599-1:2007
prEN 15599-1:2006 (E)
3.2 Symbols, units and abbreviated terms
Symbols and units used in this standard:
λ is the declared thermal conductivity W/(m·K)
D
µ is the water vapour diffusion resistance factor -

CR is the symbol of the declared value for crushing resistance
LD is the symbol of the declared value for loose bulk density
PS is the symbol of the declared particle size
ST(+) is the symbol of the declared maximum service temperature
ST(-) is the symbol of the declared minimum service temperature

Abbreviated terms used in this standard:
EPA is perlite aggregate as defined in 3.1.2.1
EPC is coated perlite as defined in 3.1.2.2
EPM is premixed perlite as defined in 3.1.2.3
ITT is initial type testing.
4 Requirements
4.1 General
Product properties shall be assessed in accordance with clause 5. To comply with this standard,
products shall meet the requirements of 4.2, and the requirements of 4.3 as appropriate.
One test result for a product property is the average of the measured values on the number of test
specimens given in Table 1.
4.2 For all applications
4.2.1 Thermal conductivity
Thermal conductivity shall be based upon measurements carried out in accordance with EN 12667 or
EN 993-14.
The thermal conductivity values shall be declared by the manufacturer in accordance with
EN ISO 13787 at reference mean temperatures covering the product service temperature range. The
following conditions apply:
 the measured values shall be expressed with three significant figures;
 the declared thermal conductivity curve shall be given as a limit curve, defined in EN ISO 13787;
 the values of the thermal conductivity, λ , shall be rounded upwards to the nearest 0,001 W/(m · K).
D
7

---------------------- Page: 9 ----------------------
oSIST prEN 15599-1:2007
prEN 15599-1:2006 (E)
4.2.2 Loose bulk density
Loose bulk density shall be determined in accordance with EN 1097-3. However the container should
be filled using a flat bottomed scoop held centrally over the container without touching it, and be no
3
more than 50 mm above the rim. The value shall be expressed as kg/m and declared by the
3
manufacturer in steps of 1 kg/m .
The loose bulk density shall be in the range of ± 15 % of the manufacturers declared value.
3 3
NOTE Most expanded perlite products are in the range 30 kg/m to 180 kg/m .
4.2.3 Particle size
4.2.3.1 Particle size distribution
Particle size distribution shall be determined in accordance with EN 933-1 without washing and
expressed as a percentage by mass, and shall be in accordance with the manufacturers declared
limits.
4.2.3.2 Size designation
The particle size shall be designated by two sieve sizes between which the main proportion of the
material lies and any undersize or oversize shall comply with 4.2.3.2 and 4.2.3.3.
The size in mm shall be selected from those specified in EN 13055-2.
NOTE The particle size will normally be in the range 0 to 16 mm.
4.2.3.3 Undersize
The content of the undersize shall not exceed 15 % by mass.
4.2.3.4 Oversize
The content of oversize shall not exceed 10 % by mass.
4.2.4 Reaction to fire
This property is not measured since expanded perlite products described by this standard are
classified without testing as class A1 products.
NOTE 1 The products are classified without testing as class A1 products in accordance with commission
decision 96/603/EC as amended by decision 2000/605/EC.
NOTE 2 Products with an organic content greater than 1 % are outside the scope of this standard.
4.2.5 Durability characteristics
4.2.5.1 General
The appropriate durability characteristics have been considered and are covered in 4.2.5.2, 4.2.5.3
and 4.2.5.4.
4.2.5.2 Durability of reaction to fire against ageing/degradation
The fire performance of expanded perlite does not change with time (see 4.2.4).
8

---------------------- Page: 10 ----------------------
oSIST prEN 15599-1:2007
prEN 15599-1:2006 (E)
4.2.5.3 Durability of thermal resistance against ageing/degradation
The thermal conductivity (4.2.1) of the product does not change with time.
4.2.5.4 Durability of compression strength against ageing/degradation
The compressive strength of expanded perlite does not change with time. Expanded perlite is a stable
cellular structure.
4.2.5.5 Durability of thermal resistance against high temperature
The thermal conductivity of exfoliated vermiculite products does not change with time at any specific
temperature within the service temperature range. This is covered by 4.3.2 maximum service
temperature (dimensional stability).
4.3 For specific applications
4.3.1 General
If there is no requirement for a property described in 4.3 for a product in use, then the property does
not need to be determined and declared by the manufacturer.
4.3.2 Maximum service temperature
The maximum service temperature, ST(+), shall be determined in accordance with annex D for loose-
fill products or prEN 14706 for bonded products.
The maximum service temperature, ST(+), shall be declared in °C in levels with steps of 50 °C.
4.3.3 Minimum service temperature
The minimum service temperature, ST(-), is not determined. Expanded perlite is stable below 0 °C.
4.3.4 Crushing resistance
In load bearing applications the crushing resistance shall be determined in accordance with
2
EN 13055-1 and expressed in N/mm .
NOTE Crushing resistance is a measure of the strength of the material but it does not necessarily relate
directly to load bearing capacity.
4.3.5 Water vapour transmission
This property is not measured because the open structure of the final product itself offers no
resistance to the free movement of water vapour.
NOTE µ, for expanded perlite may be assumed to be 3.
4.3.6 Trace quantities of water soluble ions and pH-value
Perlite is inert and trace quantities of water soluble ions and pH-value are not determined
4.3.7 Release of dangerous substances
See annex ZA.
9

---------------------- Page: 11 ----------------------
oSIST prEN 15599-1:2007
prEN 15599-1:2006 (E)
5 Test methods
5.1 Sampling
Sampling shall be carried out according to EN 932-1 and EN 932-2 using a procedure which gives a
representative sample and avoids sampling bias.
5.2 Conditioning
No special conditioning of the sample shall be used unless otherwise specified in the test method
standards. In case of dispute the test samples shall be conditioned to moisture equilibrium at
(23 ± 5) °C and (50 ± 10) % relative humidity after drying at (110 ± 5) °C.
5.3 Testing
5.3.1 General
Table 1 indicates the test procedure, the minimum number of measurements required to get one test
result and any specific conditions which are necessary.
Table 1 —Test methods, measurements and conditions
Clause Minimum number of
Specific
Test method
measurements to
conditions
No. Title
get one test result
EN 12667 or
4.2.1 Thermal conductivity 1 See annex B
EN 993-14
4.2.2 Loose bulk density EN 1097-3 3 See 4.2.2
4.2.3 Particle size EN 933-1 1 See 4.2.3
Maximum service Annex D or
4.3.2 1 None
temperature prEN 14706
Minimum service
4.3.3 Annex E 1 None
temperature
4.3.4 Crushing resistance EN 13055-1 1 None
Trace quantities of
4.3.6 water soluble ions and EN 13468 1 20g
pH-value

5.3.2 Thermal conductivity
Thermal conductivity shall be determined in accordance with EN 12667 or EN 993-14, under the
following conditions:
 at a mean temperature of (10 ± 0,3) °C;
 at different temperatures ranging from the minimum to the maximum service temperature;
 the lowest reference mean test temperature required is –10 °C;
 after preparation in accordance with the procedure given in annex B;
 after conditioning in accordance with 5.2;
10

---------------------- Page: 12 ----------------------
oSIST prEN 15599-1:2007
prEN 15599-1:2006 (E)
 the thickness of the test specimen shall be at least 10 times as thick as the mean aggregate size
in the sample.
Specimen thicknesses of 5 times the mean aggregate size are permitted if it can be shown that the
required accuracy of testing is obtained.
6 Designation code
A designation code for the product shall be given by the manufacturer. The following shall be included
except when there is no requirement for a property described in 4.3:
 Product abbreviation
 This EN standard number
 Loose bulk density LDi
 Particle size PS(x-y)
 Crushing resistance CR
 Maximum service temperature ST(+)i
 Minimum service temperature ST(-)i
 Trace quantities of water soluble chloride ions CLi
 Trace quantities of water soluble fluoride ions FLi
where “i” shall be used to indicate the relevant class or level, and (x-y) indicates the upper and lower
sieve size.
The designation code for an expanded perlite product is illustrated by the following example:
EPA EN xxxxx – LD80 - PS(4-8) - ST(+)650 - ST(-)-200
7 Evaluation of conformity
The manufacturer or their authorised representative shall be responsible for the conformity of the
product with the requirements of this European Standard. The evaluation of conformity shall be
carried out in accordance with EN 13172 and shall be based on initial type tests, factory production
control and tests on samples taken at the factory.
If a manufacturer decides to group their products it shall be done in accordance with EN 13172.
ITT shall be carried out in accordance with EN 13172 for all characteristics declared, except for
thermal conductivity. ITT for the thermal conductivity curve shall be carried out according to
EN ISO 13787.
For ITT testing of the λ curve and the maximum and minimum service temperatures only one test
result is required using test specimens from four different production dates.
FPC testing shall be made for the characteristics listed in annex A.
The minimum frequencies of tests in the factory production control shall be in accordance with
annex A.
When indirect testing is used, the correlation to direct testing shall be established in accordance with
EN 13172.
11

---------------------- Page: 13 ----------------------
oSIST prEN 15599-1:2007
prEN 15599-1:2006 (E)
The manufacturer or his authorised representative shall make available, in response to a request, a
certificate or declaration of conformity as appropriate.
NOTE The system of attestation of conformity for the CE marking of the product is chosen in accordance
with annex ZA of this standard.
8 Marking and labelling
Products complying with this standard shall be clearly marked, either on the packa
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27