|
SLOVENSKI STANDARD
01-junij-2022
Aeronavtika - Nekovinski materiali - Pravila za pripravo in predstavitev tehničnih
specifikacij
Aerospace series - Non-metallic materials - Rules for drafting and presentation of
technical specifications
Luft- und Raumfahrt - Nichtmetallische Werkstoffe - Regeln für die Abfassung und
Gestaltung von Techischen Lieferbedingungen
Série aérospatiale - Matériaux non-métalliques - Règles pour la rédaction et la
présentation des spécifications techniques
Ta slovenski standard je istoveten z: EN 4387:2022
ICS:
49.025.99 Drugi materiali Other materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 4387
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2022
EUROPÄISCHE NORM
ICS 49.025.99
English Version
Aerospace series - Non-metallic materials - Rules for
drafting and presentation of technical specifications
Série aérospatiale - Matériaux non-métalliques - Règles Luft- und Raumfahrt - Nichtmetallische Werkstoffe -
pour la rédaction et la présentation des spécifications Regeln für die Abfassung und Gestaltung von
techniques Technischen Lieferbedingungen
This European Standard was approved by CEN on 8 December 2019.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 4387:2022 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Framework and structure . 5
4.1 General . 5
4.2 Required elements . 6
5 Content . 6
5.1 Title . 6
5.2 Introduction . 6
Clause 1: Scope . 7
Clause 2: Normative references . 7
Clause 3: Terms and definitions . 7
Clause 4: Requirements . 8
Clause 5: Qualification . 9
5.3 Clause 6: Release testing . 11
5.4 Clause 7: Preparation for delivery . 12
5.5 Clause 8: Declaration of conformity . 13
Annex A: Testing requirement tables . 14
Annex A (normative) Modified rules for the preparation of technical specifications
containing more than one part . 18
A.1 Introduction . 18
A.2 Framework and structure of specific parts . 18
A.2.1 Title . 18
A.2.2 Scope . 18
A.2.4 Terms and definitions . 19
Bibliography . 21
European foreword
This document (EN 4387:2022) has been prepared by the Aerospace and Defence Industries Association
of Europe — Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of
ASD-STAN, prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2022, and conflicting national standards shall
be withdrawn at the latest by October 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United
Kingdom.
Introduction
This document is part of the series of EN non-metallic materials standards for aerospace applications.
The general organisation of this series is described in EN 4385. This document is a level 2 document as
defined in EN 4385.
1 Scope
This document specifies the general rules for drafting and presentation of EN aerospace series non-
metallic material technical specifications.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 4385, Aerospace series — Non-metallic materials — General organisation of standardisation — Links
1)
between types of standards
TR 7000-1, Aerospace series — Non-metallic materials —Rules for the drafting and presentation of
)
material standards — Part 1: General rules
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at
— IEC Electropedia: available at
4 Framework and structure
4.1 General
Where necessary the technical specification may be subdivided into several parts (e.g. EN XXXX-001,
EN XXXX-002, etc., where Part 001 is always the general part).
In such cases all general requirements should be incorporated in Part 001 (general part) and the specific
requirements in Part 002 onwards (specific parts). Annex A gives modified rules for the preparation of
technical specifications containing more than one part.
)
Published as ASD-STAN Technical Report at the date of publication of this document (see www.asd-stan.org).
4.2 Required elements
The technical specification shall include the title and the following elements in the given order:
— Introduction;
— Clause – 1 Scope;
— Clause – 2 Normative references;
— Clause – 3 Terms and definitions;
— Clause – 4 Requirements;
— Clause – 5 Qualification;
— Clause – 6 Release testing;
— Clause – 7 Preparation for delivery;
— Clause – 8 Declaration of conformity;
— Annex A Testing requirements tables.
All of the above clauses and their subclauses, with the exception of the Introduction, are mandatory. If any
of the mandatory clauses and/or subclauses are not applicable, the number and heading shall still be used
with the statement "Not Applicable".
5 Content
Standard sentences, placed in a frame, are listed below for the different clauses and subclauses of the
technical specification and are mandatory unless otherwise stated.
When necessary, further information is indicated in italics, shall be completed or re-worded.
5.1 Title
This title shall give sufficient information to unambiguously identify the subject of this document.
EXAMPLE
Aerospace series
Non-metallic materials
Family(ies) (e.g. film adhesives, organic materials)
Add additional information, if necessary (e.g. cure temperature)
5.2 Introduction
This clause is optional. If included, the following standard wording shall be used.
EXAMPLE
Introduction
This document is part of the series of EN non-metallic material standards for aerospace applications.
The general organization of this series is described in EN 4385. This document is a level 2 document
as defined in EN 4385.
This document has been prepared in accordance with EN 4387.
5.3 Clause 1: Scope
In this clause, the scope and field of application of the technical specification shall be stated.
EXAMPLE
1 Scope
This document defines the requirements for manufacture, qualification, inspection and testing of
(complete with non-metallic material family, e.g. glass reinforced thermosetting preimpregnates) for
aerospace applications.
5.4 Clause 2: Normative references
EXAMPLE
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
(Followed by the list of documents; give titles to which reference is made in the text and date of issue
if required)
5.5 Clause 3: Terms and definitions
EXAMPLE
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 9100 and EN 9133 and the
following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
− ISO Online browsing platform: available at
− IEC Electropedia: available at
3.1
batch
(define the batch of the material family)
3.2
product
in this document, the word product refers to all forms of (repeat non-metallic material family name
from 1 Scope)
3.3 (add additional definitions, if necessary)
5.6 Clause 4: Requirements
This clause shall contain technical requirements for the manufacture, qualification, inspection and testing
of the products.
This clause is subdivided into 2 (two) subclauses:
• Subclause 4.1: General requirements;
• Subclause 4.2: Technical requirements.
EXAMPLE
4 Requirements
4.1 General requi
...