|
SIST EN 13114:2003/kFprA1:2009
01-junij-2009
6WURMDUVNLVWURML9UWHþHVHSURFHVQHSRVRGH9DUQRVWQH]DKWHYH
Tannery machines - Rotating process vessels - Safety requirements
Gerberei-Maschinen - Rotierende Bearbeitungsgefäße - Sicherheitsanforderungen
Machines de tannerie - Tonneaux tournants - Prescriptions de sécurité
Ta slovenski standard je istoveten z: EN 13114:2002/FprA1
ICS:
59.140.40 Stroji in oprema za Machines and equipment for
proizvodnjo usnja in krzna leather and fur production
SIST EN 13114:2003/kFprA1:2009 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 13114:2003/kFprA1:2009
---------------------- Page: 2 ----------------------
SIST EN 13114:2003/kFprA1:2009
EUROPEAN STANDARD
FINAL DRAFT
EN 13114:2002
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA1
April 2009
ICS 59.140.40
English Version
Tannery machines - Rotating process vessels - Safety
requirements
Machines de tannerie - Tonneaux tournants - Prescriptions Gerberei-Maschinen - Rotierende Bearbeitungsgefäße -
de sécurité Sicherheitsanforderungen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 200.
This draft amendment A1, if approved, will modify the European Standard EN 13114:2002. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13114:2002/FprA1:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 13114:2003/kFprA1:2009
EN 13114:2002/FprA1:2009 (E)
Foreword
This document (EN 13114:2002/FprA1:2009) has been prepared by Technical Committee CEN/TC 200
“Tannery machinery - Safety”, the secretariat of which is held by UNI.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document.
The first reason for amending the published standard EN 13114:2002 is the revision of the EU-Machinery
Directive 98/37/EC into 2006/42/EC, requiring the adaptation of published European Standards cited in the
Official Journal of the European Communities under that Directive.
Additionally at this occasion the normative references have been updated, while also some other limited rather
editorial improvements and corrections have been made.
2
---------------------- Page: 4 ----------------------
SIST EN 13114:2003/kFprA1:2009
EN 13114:2002/FprA1:2009 (E)
1 Modification to the Foreword
th
Replace the existing 4 paragraph with the following: "For relationship with EU Directive(s), see informative
Annexes ZA and ZB, which are integral parts of this document.".
2 Modification to the Introduction
Replace the complete text with the following:
"This document is a type C standard as stated in EN ISO 12100.
The machinery concerned and the extent to which hazards, hazardous situations and hazardous events are
covered are indicated in the scope of this document.
When provisions of this type C standard are different from those which are stated in type A or B standards, the
provisions of this type C standard take precedence over the provisions of the other standards, for machines
that have been designed and built according to the provisions of this type C standard.".
3 Modification to Clause 1, Scope
1.5:
Replace the text with the following: "This document is not applicable to the rotating vessels
...