|
SLOVENSKI STANDARD
01-september-2022
Nadomešča:
SIST EN ISO 13696:2002
Optika in optični instrumenti - Preskusne metode za sevanje, razpršeno z
optičnimi komponentami (ISO 13696:2022)
Optics and photonics - Test method for total scattering by optical components (ISO
13696:2022)
Optik und Photonik - Bestimmung von totaler Streustrahlung, hervorgerufen durch
optische Komponenten (ISO 13696:2022)
Optique et photonique - Méthodes d’essai du rayonnement diffusé par les composants
optiques (ISO 13696:2022)
Ta slovenski standard je istoveten z: EN ISO 13696:2022
ICS:
31.260 Optoelektronika, laserska Optoelectronics. Laser
oprema equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 13696
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2022
EUROPÄISCHE NORM
ICS 31.260 Supersedes EN ISO 13696:2002
English Version
Optics and photonics - Test method for total scattering by
optical components (ISO 13696:2022)
Optique et photonique - Méthodes d'essai du Optik und Photonik - Bestimmung von totaler
rayonnement diffusé par les composants optiques (ISO Streustrahlung, hervorgerufen durch optische
13696:2022) Komponenten (ISO 13696:2022)
This European Standard was approved by CEN on 21 May 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13696:2022 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 13696:2022) has been prepared by Technical Committee ISO/TC 172 "Optics
and photonics" in collaboration with Technical Committee CEN/TC 123 “Lasers and photonics” the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2022, and conflicting national standards
shall be withdrawn at the latest by December 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 13696:2002.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 13696:2022 has been approved by CEN as EN ISO 13696:2022 without any modification.
INTERNATIONAL ISO
STANDARD 13696
Second edition
2022-06
Optics and photonics — Test method
for total scattering by optical
components
Optique et photonique — Méthodes d'essai du rayonnement diffusé
par les composants optiques
Reference number
ISO 13696:2022(E)
ISO 13696:2022(E)
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: [email protected]
Website: www.iso.org
Published in Switzerland
ii
ISO 13696:2022(E)
Contents Page
Foreword .iv
Introduction . vi
1 Scope . 1
2 Normative references . 1
3 Terms, definitions and symbols . 1
3.1 Terms and definitions . 1
3.2 Symbols and units of measure . . 3
4 Test method . 3
4.1 Principle . 3
4.2 Measurement arrangement and test equipment . 3
4.2.1 General . 3
4.2.2 Radiation source . 4
4.2.3 Beam preparation system . 4
4.2.4 Integrating sphere . 5
4.2.5 Detection system. 6
4.2.6 Specimen holder . 6
4.3 Arrangement with high sensitivity . 6
4.4 Preparation of specimens . 7
5 Procedure .7
5.1 General . 7
5.2 Alignment procedure . 8
5.2.1 General . 8
5.2.2 Alignment of the beam . 8
5.2.3 Alignment of the specimen . 8
5.3 Measurement procedure . 8
6 Evaluation . 9
6.1 Determination of the total scattering value . 9
6.2 Error budget .12
7 Test report .12
Annex A (informative) Set-up with a Coblentz hemisphere .14
Annex B (informative) Example of test report .17
Annex C (informative) Statistical evaluation example .21
Annex D (informative) Example for selection of spacing .26
Annex E (informative) Alternative method for calibrating total scatter measurements
using a calcium fluoride diffuser disk .29
Bibliography .31
iii
ISO 13696:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related
...