EN 17391:2022

Non-destructive testing - Acoustic emission testing - In-service acoustic emission monitoring of metallic pressure equipment and structures - General requirements

EN 17391:2022

Name:EN 17391:2022   Standard name:Non-destructive testing - Acoustic emission testing - In-service acoustic emission monitoring of metallic pressure equipment and structures - General requirements
Standard number:EN 17391:2022   language:English language
Release Date:28-Jun-2022   technical committee:CEN/TC 138 - Non-destructive testing
Drafting committee:CEN/TC 138/WG 7 - Acoustic emission testing   ICS number:19.100 - Non-destructive testing

SLOVENSKI STANDARD
01-november-2022
Neporušitvene preiskave - Akustična emisija - Nadzorovanje akustične emisije pri
uporabi kovinske tlačne opreme in drugih kovinskih struktur - Splošne zahteve
Non-destructive testing - Acoustic emission testing - Inservice acoustic emission
monitoring of metallic pressure equipment and structures - General requirements
Zerstörungsfreie Prüfung - Schallemissionsprüfung - Überwachung der Schallemission
von metallischen Druckgeräten und -strukturen im Betrieb - Allgemeine Grundsätze
Essais non destructifs - Contrôle par émission acoustique - Surveillance en service par
émission acoustique des équipements et structures métalliques sous pression -
Exigences générales
Ta slovenski standard je istoveten z: EN 17391:2022
ICS:
19.100 Neporušitveno preskušanje Non-destructive testing
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 17391
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2022
EUROPÄISCHE NORM
ICS 19.100
English Version
Non-destructive testing - Acoustic emission testing - In-
service acoustic emission monitoring of metallic pressure
equipment and structures - General requirements
Essais non destructifs - Contrôle par émission Zerstörungsfreie Prüfung - Schallemissionsprüfung -
acoustique - Surveillance en service par émission Überwachung der Schallemission von metallischen
acoustique des équipements et structures métalliques Druckgeräten und Strukturen im Betrieb - Allgemeine
sous pression - Exigences générales Grundsätze
This European Standard was approved by CEN on 5 March 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 17391:2022 E
worldwide for CEN national Members.

Contents Page
European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Personnel qualification . 6
5 Information prior to testing . 7
5.1 Structural information . 7
5.2 Operating conditions . 7
5.3 AE event mechanisms . 8
5.3.1 General. 8
5.3.2 Crack growth . 8
5.3.3 Corrosion . 9
5.3.4 Friction, fretting and cavitation erosion . 9
6 Monitoring methodology . 9
6.1 Periodic, temporary or continuous monitoring . 9
6.2 On-site or remote-controlled monitoring . 10
6.3 Supervised or automated monitoring . 11
7 Monitoring instrumentation . 11
7.1 System requirements . 11
7.2 Sensors and preamplifiers. 11
7.2.1 General requirements . 11
7.2.2 Frequency range (band width) . 12
7.2.3 Coupling agent . 13
7.2.4 Mounting method . 13
7.2.5 Temperature range, wave guide usage . 13
7.2.6 Use in explosive atmosphere . 13
7.2.7 Immersed sensors . 13
7.2.8 Integral electronics (amplifier, band-pass filter, RMS converter, ASL converter) . 13
7.2.9 Grounding . 14
7.2.10 External preamplifiers . 14
7.2.11 Sensor and preamplifier cables . 14
7.3 Portable AE equipment . 14
7.4 Single channel and multi-channel AE equipment . 14
7.5 Measured parameters . 14
7.5.1 Burst signal parameters . 14
7.5.2 Continuous signal parameters . 15
7.6 Verification of sensor sensitivity and coupling quality . 15
7.7 External parameters . 15
7.8 AE system . 15
7.9 Monitoring in hazardous areas . 16
8 Pre-monitoring measurements . 16
8.1 Wave propagation behaviour . 16
8.1.1 General. 16
8.1.2 Liquid or gas containment . 17
8.1.3 Wall thickness . 17
8.1.4 Geometry of the structure . 17
8.1.5 Insulation . 17
8.1.6 Surface preparation . 17
8.2 Background noise measurement . 17
8.2.1 Representative location . 17
8.2.2 Process noise . 18
8.2.3 Other disturbance noise . 18
8.2.4 Noise sampling period . 18
8.3 Sensitivity of AE monitoring using linear or planar location . 18
9 Monitoring procedure . 19
9.1 Sensor positioning . 19
9.2 External parameters . 19
9.3 Instrumentation verification . 19
9.4 Data acquisition and online filtering . 19
10 Data analysis . 20
10.1 General . 20
10.2 Online analysis . 20
10.3 Data processing . 20
10.3.1 General . 20
10.3.2 Background noise analysis . 20
10.3.3 Pre-location data analysis . 21
10.3.4 AE event location . 21
10.3.5 Cluster analysis . 22
10.3.6 Pattern recognition . 22
11 AE source interpretation and evaluation . 22
11.1 Interpretation of AE results . 22
11.2 Source evaluation criteria .
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27