prEN 81-7

Safety rules for the construction and installation of lifts and service lifts - Part 7: Rack and pinion lifts

prEN 81-7

Name:prEN 81-7   Standard name:Safety rules for the construction and installation of lifts and service lifts - Part 7: Rack and pinion lifts
Standard number:prEN 81-7   language:English language
Release Date:24-Jul-2012   technical committee:CEN/TC 10 - Passenger, goods and service lifts
Drafting committee:CEN/TC 10/WG 1 - Lifts and service lifts   ICS number:91.140.90 - Lifts. Escalators
SLOVENSKI STANDARD
oSIST prEN 81-7:2009
01-junij-2009
Varnostna pravila za konstruiranje in vgradnjo dvigal (liftov) - 7. del: Dvigala z
zobnikom in zobato letvijo
Safety rules for the construction and installation of lifts - Part 7: Rack and pinion lifts
Sicherheitsregeln für die Konstruktion und den Einbau von Aufzügen - Teil 7:
Zahnstangenaufzüge
Règles de sécurité pour la construction et l'installation des ascenseurs - Partie 7:
Ascenseurs à pignon et crémaillère
Ta slovenski standard je istoveten z: prEN 81-7
ICS:
91.140.90 'YLJDOD7HNRþHVWRSQLFH Lifts. Escalators
oSIST prEN 81-7:2009 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 81-7:2009

---------------------- Page: 2 ----------------------
oSIST prEN 81-7:2009
EUROPEAN STANDARD
DRAFT
prEN 81-7
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2009
ICS

English Version
Safety rules for the construction and installation of lifts - Part 7:
Rack and pinion lifts
Règles de sécurité pour la construction et l'installation des Sicherheitsregeln für die Konstruktion und den Einbau von
ascenseurs - Partie 7: Ascenseurs à pignon et crémaillère Aufzügen - Teil 7: Zahnstangenaufzüge
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 10.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 81-7:2009: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 81-7:2009
prEN 81-7:2009 (E)

Contents Page
Foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 List of significant hazards . 6
5 Safety requirements and for protective measures . 9
6 Verification of safety measures and for protective measures . 25
7 Information for use . 29
Annex A (normative) List of the electric safety devices . 30
Annex C (informative) Technical dossier . 31
Annex D (normative) Examinations and test before putting into service . 33
Annex E (informative) Periodical examinations and tests, examinations and tests after an
important modification or after an accident.
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27