|
oSIST prEN 15014:2014
01-julij-2014
Cevni sistemi iz polimernih materialov - Podzemne in nadzemne cevne
komponente za vodo pod tlakom - Zahteve in preskusi/metode ocenjevanja za cevi
in fitinge
Plastics piping systems - Buried and above ground piping components for water under
pressure - Requirements and test/assessment methods for pipes and fittings
Kunststoff-Rohrleitungssysteme - Erdverlegte und oberirdische Rohrleitungsteile für
Wasser unter Druck - Anforderungen und Prüf-/Beurteilungsmethoden für Rohre und
Formstücke
Systèmes de canalisations en plastique - Composants de canalisation enterrés et
aériens pour eau avec pression - Exigences et méthodes d’essais/d’évaluation pour
tubes et raccords
Ta slovenski standard je istoveten z: prEN 15014
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
23.040.45 Fitingi iz polimernih Plastics fittings
materialov
91.140.80 Drenažni sistemi Drainage systems
oSIST prEN 15014:2014 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 15014:2014
---------------------- Page: 2 ----------------------
oSIST prEN 15014:2014
EUROPEAN STANDARD
DRAFT
prEN 15014
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2014
ICS 23.040.20; 23.040.45 Will supersede EN 15014:2007
English Version
Plastics piping systems - Buried and above ground piping
components for water under pressure - Requirements and
test/assessment methods for pipes and fittings
Systèmes de canalisations en plastique - Composants de Kunststoff-Rohrleitungssysteme - Erdverlegte und
canalisation enterrés et aériens pour eau avec pression - oberirdische Rohrleitungsteile für Wasser unter Druck -
Exigences et méthodes d'essais/d'évaluation pour tubes et Anforderungen und Prüf-/Beurteilungsmethoden für Rohre
raccords und Formstücke
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 155.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 15014:2014 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 15014:2014
prEN 15014:2014 (E)
Contents Page
Foreword .4
Introduction .5
1 Scope .6
2 Normative references .6
3 Terms, definitions and abbreviations .9
3.1 Terms and definitions .9
3.2 Abbreviations . 10
4 Product characteristics .
...