|
SLOVENSKI STANDARD
01-maj-2018
'LQDPLþQLPRGXOLGHO 3UHVNXVQHPHWRGH[1:66VILNVQRPUHåR
0HUMHQMHGLQDPLþQHJDSUHVOXKD ,(&
Dynamic modules - Part 5-2: Test methods - 1xN fixed-grid WSS - Dynamic crosstalk
measurement (IEC 62343-5-2:2018)
Ta slovenski standard je istoveten z: EN IEC 62343-5-2:2018
ICS:
33.180.01 6LVWHPL]RSWLþQLPLYODNQLQD Fibre optic systems in
VSORãQR general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 62343-5-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2018
ICS 33.180.01, 33.180.99
English Version
Dynamic modules - Part 5-2: Test methods - 1xN fixed-grid WSS
- Dynamic crosstalk measurement
(IEC 62343-5-2:2018)
Modules dynamiques - Partie 5-2: Méthodes d'essai - Dynamische Module - Teil 5-2: Prüfverfahren - 1×N-
Commutateurs sélectifs en longueur d'onde à grille fixe 1 x Festraster-WSS - Messung des dynamischen
N - Mesure de diaphonie dynamique Übersprechens
(IEC 62343-5-2:2018) (IEC 62343-5-2:2018)
This European Standard was approved by CENELEC on 2018-02-19. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 62343-5-2:2018 E
European foreword
The text of document 86C/1449/CDV, future edition 1 of IEC 62343-5-2, prepared by IEC/SC 86C
"Fibre optic systems and active devices" of IEC/TC 86 "Fibre optics" was submitted to the IEC-
CENELEC parallel vote and approved by CENELEC as EN IEC 62343-5-2:2018.
The following dates are fixed:
• latest date by which the document has to be (dop) 2018-11-19
implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2021-02-19
• latest date by which the national
standards conflicting with the
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 62343-5-2:2018 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 61300-3-50 NOTE Harmonized as EN 61300-3-50.
IEC 62343-3-3:2014 NOTE Harmonized as EN 62343-3-3:2014 (not modified).
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 61300-3-29 - Fibre optic interconnecting devices and EN 61300-3-29 -
passive components - Basic test and
measurement procedures -- Part 3-29:
Examinations and measurements -
Spectral transfer characteristics of DWDM
devices
IEC 62343 - Dynamic modules - General and guidance EN 62343 -
IEC/TR 61931 - Fibre optic - Terminology - -
IEC/TS 62538 - Categorization of optical devices - -
ISO/IEC Guide 99 - International vocabulary of metrology - - -
Basic and general concepts and
associated terms (VIM)
IEC 62343-5-2
Edition 1.0 2018-01
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Dynamic modules –
Part 5-2: Test methods – 1 x N fixed-grid WSS – Dynamic crosstalk measurement
Modules dynamiques –
Partie 5-2: Méthodes d'essai – Commutateurs sélectifs en longueur d'onde à grille
fixe 1 x N – Mesure de diaphonie dynamique
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.180.01 33.180.99 ISBN 978-2-8322-5267-3
– 2 – IEC 62343-5-2:2018 © IEC 2018
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions and abbreviated terms . 6
3.1 Basic terms . 6
3.2 Performance parameter terms . 8
3.3 Abbreviated terms . 9
4 Apparatus . 10
4.1 Test set-up . 10
4.2 Light source . 10
4.2.1 Tuneable laser source (TLS) . 10
4.2.2 Broadband light source and tuneable filter . 11
4.3 Device under test . 11
4.4 Detector . 12
4.4.1 Optical power meter (OPM) . 12
4.4.2 OE converter and oscilloscope . 12
5 Measurement condition . 13
5.1 General conditions . 13
5.2 Recommendations on selections of a branching port and channel . 13
6 Procedure . 13
6.1 Preparation . 13
6.2 Measurement . 14
6.2.1 Measurement of input power and insertion loss of DUT . 14
6.2.2 Measurement of noise power for dynamic crosstalk . 14
6.2.3 Measurement of noise power for different channel crosstalk . 14
6.2.4 Measurement of noise power for same channel crosstalk . 14
7 Example of transient characteristics of noise power . 15
8 Calculation . 17
9 Measurement report . 19
Bibliography . 21
Figure 1 – Noise observed in port during conducting port switching in 1 x N WSS . 9
Figure 2 – Test set-up to measure dynamic crosstalk . 10
Figure 3 – Transient characteristics for measurement of different channel dynamic
crosstalk . 16
Figure 4 – Transient characteristics for measurement of same channel dynamic
crosstalk . 17
Table 1 – Example of template for measurement results for different channel dynamic
crosstalk . 19
Table 2 – Example of summary of crosstalk measurement . 20
IEC 62343-5-2:2018 © IEC 2018 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
DYNAMIC MODULES –
Part 5-2: Test methods – 1 x N fixed-grid WSS –
Dynamic crosstalk measurement
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC
Publication(s)"). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of
...