|
SLOVENSKI STANDARD
01-junij-2021
Nadomešča:
SIST EN 62053-22:2004
SIST EN 62053-22:2004/A1:2017
SIST EN 62053-22:2004/A1:2017/AC:2018
Oprema za merjenje električne energije - Posebne zahteve - 22. del: Statični števci
delovne energije (razredi 0,1 S, 0,2 S in 0,5 S)
Electricity metering equipment - Particular requirements - Part 22: Static meters for AC
active energy (classes 0,1S, 0,2S and 0,5S)
Ta slovenski standard je istoveten z: EN IEC 62053-22:2021
ICS:
17.220.20 Merjenje električnih in Measurement of electrical
magnetnih veličin and magnetic quantities
91.140.50 Sistemi za oskrbo z elektriko Electricity supply systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 62053-22
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2021
ICS 17.220.20 Supersedes EN 62053-22:2003 and all of its
amendments and corrigenda (if any)
English Version
Electricity metering equipment - Particular requirements - Part
22: Static meters for AC active energy
(classes 0,1S, 0,2S and 0,5S)
(IEC 62053-22:2020)
Équipement de comptage de l'électricité - Exigences Elektrizitätszähler - Besondere Anforderungen - Teil 22:
particulières - Partie 22: Compteurs statiques d'énergie Elektronische Wirkverbrauchszähler für Wechselstrom der
active en courant alternatif (classes 0,1 S, 0,2 S et 0,5 S) Genauigkeitsklassen 0,1 S, 0,2 S und 0,5 S
(IEC 62053-22:2020) (IEC 62053-22:2020)
This European Standard was approved by CENELEC on 2020-07-22. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 62053-22:2021 E
European foreword
The text of document 13/1806A/FDIS, future edition 2 of IEC 62053-22, prepared by IEC/TC 13
"Electrical energy measurement and control" was submitted to the IEC-CENELEC parallel vote and
approved by CENELEC as EN IEC 62053-22:2021.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2021-10-02
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2024-04-02
document have to be withdrawn
This document supersedes EN 62053-22:2003 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association.
Endorsement notice
The text of the International Standard IEC 62053-22:2020 was approved by CENELEC as a European
Standard without any modification.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 62052-11 2020 Electricity metering equipment - General EN IEC 62052-11 2021
requirements, tests and test conditions -
Part 11: Metering equipment
IEC 62053-22
Edition 2.0 2020-06
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Electricity metering equipment – Particular requirements –
Part 22: Static meters for AC active energy (classes 0,1S, 0,2S and 0,5S)
Équipement de comptage de l'électricité – Exigences particulières –
Partie 22: Compteurs statiques d'énergie active en courant alternatif
(classes 0,1 S, 0,2 S et 0,5 S)
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 17.220.20 ISBN 978-2-8322-8439-1
– 2 – IEC 62053-22:2020 © IEC 2020
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 8
2 Normative references . 9
3 Terms and definitions . 9
4 Standard electrical values. 9
4.1 Voltages . 9
4.2 Currents . 9
4.2.1 Nominal currents . 9
4.2.2 Starting current . 10
4.2.3 Minimum current . 10
4.2.4 Maximum current . 10
4.3 Frequencies . 10
4.4 Power consumption . 10
5 Construction requirements . 10
6 Meter marking and documentation . 10
7 Accuracy requirements . 10
7.1 General test conditions . 10
7.2 Methods of accuracy verification . 10
7.3 Measurement uncertainty . 11
7.4 Meter constant . 11
7.5 Initial start-up of the meter . 11
7.6 Test of no-load condition . 11
7.7 Starting current test . 11
7.8 Repeatability test . 11
7.9 Limits of error due to variation of the current . 11
7.10 Limits of error due to influence quantities . 12
7.11 Time-keeping accuracy . 14
8 Climatic requirements . 14
9 The effects of external influences . 14
10 Type test . 14
Annex A (informative) Comparison of acceptable percentage error limits at reference
conditions for meters of classes 0,1 S, 0,2 S, and 0,5 S . 15
Annex B (informative) Summary of changes . 17
Figure A.1 – Comparison of acceptable percentage error limits for meters of classes
0,1 S, 0,2 S,and 0,5 S, with I = 5 A and I = 10 A, at PF = 1,0 . 15
n max
Figure A.2 – Comparison of acceptable percentage error limits for meters of classes
0,1 S, 0,2 S, and 0,5 S, with I = 5 A and I = 10 A, at PF = 0,5 inductive or PF = 0,8
n max
capacitive . 16
Table 1 – Starting current . 10
Table 2 – Minimum current. 10
Table 3 – Acceptable percentage error limits (single-phase meters and poly-phase
meters with balanced loads or single-phase loads) . 12
IEC 62053-22:2020 © IEC 2020 – 3 –
Table 4 – Acceptable limits of variation in percentage error due to influence quantities . 13
– 4 – IEC 62053-22:2020 © IEC 2020
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ELECTRICITY METERING EQUIPMENT –
PARTICULAR REQUIREMENTS –
Part 22: Static meters for AC active energy (classes 0,1 S, 0,2 S and 0,5 S)
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants
...