EN 50632-2-17:2016/A1:2021

Electric motor-operated tools - Dust measurement procedure - Part 2-17: Particular requirements for routers and trimmers

EN 50632-2-17:2016/A1:2021

Name:EN 50632-2-17:2016/A1:2021   Standard name:Electric motor-operated tools - Dust measurement procedure - Part 2-17: Particular requirements for routers and trimmers
Standard number:EN 50632-2-17:2016/A1:2021   language:English language
Release Date:23-Sep-2021   technical committee:CLC/TC 116 - Safety of hand-held motor-operated electric tools
Drafting committee:CLC/TC 116/WG 04 - Dust   ICS number:13.040.40 - Stationary source emissions

SLOVENSKI STANDARD
01-november-2021
Elektromotorna orodja - Postopek meritve prahu - 2-17. del: Posebne zahteve za
rezkalnike in obrezovalnike - Dopolnilo A1
Electric motor-operated tools - Dust measurement procedure - Part 2-17: Particular
requirements for routers and trimmers
Motorbetriebene Elektrowerkzeuge - Staubmessverfahren - Teil 2-17: Besondere
Anforderungen für Oberfräsen und Kantenfräsen
Outils électriques à moteur - Procédure de mesure de la poussière - Partie 2-17:
Exigences particulières pour les défonceuses
Ta slovenski standard je istoveten z: EN 50632-2-17:2016/A1:2021
ICS:
25.100.01 Rezalna orodja na splošno Cutting tools in general
25.140.20 Električna orodja Electric tools
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 50632-2-17:2016/A1

NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2021
ICS 13.040.40; 25.140.20; 65.060.80
English Version
Electric motor-operated tools - Dust measurement procedure -
Part 2-17: Particular requirements for routers and trimmers
Outils électriques à moteur - Procédure de mesure de la Motorbetriebene Elektrowerkzeuge - Staubmessverfahren -
poussière - Partie 2-17: Exigences particulières pour les Teil 2-17: Besondere Anforderungen für Oberfräsen und
défonceuses Kantenfräsen
This amendment A1 modifies the European Standard EN 50632-2-17:2016; it was approved by CENELEC on 2021-08-09. CENELEC
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the
status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as
the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 50632-2-17:2016/A1:2021 E

Contents Page
European foreword . 3
1 Modification to the European foreword . 4
2 Modifications to 4.3, “Operating conditions” . 4
3 Addition of Figures 101 and 102 . 6

European foreword
This document (EN 50632-2-17:2016/A1:2021) has been prepared by CLC/TC 116 “Safety and environmental
aspects of motor-operated electric tools”.
The following dates are fixed:
• latest date by which this document has to be (dop) 2022-08-09
implemented at national level by publication of
an identical national standard or by
endorsement
• latest date by which the national standards (dow) 2024-08-09
conflicting with this document have to be
withdrawn
This amendment was developed to include improvements and clarifications suggested by practical tests.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to th
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27