The base of the wind turbine is an important part of the wind turbine. It supports the weight of the entire wind turbine and must also resist the enormous force brought by the wind. Therefore, the design and structure of the wind turbine base is very important.
Design points
The design points of the wind turbine base mainly include the following aspects:
1. Load capacity: The base of the wind turbine must support the load. all wind energy The weight of the generator must also withstand the enormous force brought by the wind. Therefore, the bearing capacity of the base must be strong enough.
2. Stability: The base of the wind turbine must have good stability to ensure that the entire wind turbine will not tilt or collapse under the action of the wind.
3. Durability: The wind turbine base must have good durability to ensure that it will not be damaged or deformed whenof long-term use.
Structural characteristics
The structural characteristics of the wind turbine base mainly include the following aspects:
1. Base part: The base part of the wind turbine base. is usually It is cast in concrete to ensure sufficient bearing capacity and stability.
2. Support structure: The support structure of the wind turbine base is usually made of steel or concrete to ensure sufficient strength and stability.
3. Connection part: The connection part of the wind turbine base is usually bolted or welded to ensure sufficient connection strength and stability.
Application scenario analysis of wind turbine base
Wind turbine base is mainly used in wind farms. Its main function is to support the wind turbine and resist the force of the wind. Application scenarios of the basicswind turbines mainly include the following aspects:
1. Lowland areas: Lowland areas generally have less wind, so taller wind turbines are required to achieve sufficient energy production. In this case, the wind turbine base must have sufficient bearing capacity and stability to ensure the safe operation of the entire wind turbine.
2. Mountainous areas: Mountainous areas generally have stronger winds, so weaker wind turbines are required to achieve sufficient electricity generation. In this case, the wind turbine base must have sufficient stability and durability to ensure that the entire wind turbine will not tilt or collapse under the action of strong winds.
3. Offshore Wind Farms: Offshore wind farms are typically subject to strong winds and must withstand the impact of waves. In this case, the base of the wind turbine must have a durableSufficient ility and stability to ensure that the entire wind turbine will not tilt or collapse under wave action.
The operation steps of the wind turbine base
The operation steps of the wind turbine base mainly include the following aspects:
1 . Foundation Construction: Firstly, it should be carried out Foundation construction, including digging foundation pits, building formwork, pouring concrete and other steps.
2. Install the support structure: After the foundation construction is completed, the support structure must be installed, including support columns, support rings and other steel or concrete parts.
3. Install the connecting part: After the support structure is installed, the connecting part needs to be installed, including steps such as bolted connections or welded connections.
4. Install the wind turbine: After the connection part is installed, the wind turbine needs to be installed and connected to the base.
5. Debugging and testing: After the installation is completed, the entire wind turbine needs to be debugged and tested to ensure its normal operation.
First, you need a generator motor. If you are making a micro wind turbine, the engine from a four-wheel drive vehicle can be used instead. Then you install a generator. The front rotor head of the engine. Install the wings you made to cause the wind. When the wind turns the motor rotor, both ends of the wire at the rear end of the motor can generate electricity. wind turbine, but that's fair. It can produce electricity but has no practical use.
Secondly, if you need a really practical micro wind turbine, you need to do the following steps and prepare some materials, such as diode and voltage regulator (voltage stabilizing circuit board), battery. , etc.
When preparing these materials, you can first connect one end of the generator motor wire to a diode to prevent the generated power from flowing back to the motor, then connect it to the voltage regulator (a reminder here) The voltage stabilizing power of the voltage stabilizer should be determined in advance, and it must meet the parameter requirements of the voltage generated by the motor to prevent the voltage stabilizing circuit board from burning) before connecting the battery to the voltage stabilizer (the battery voltage should also be stable. (within the rated parameters of the voltage regulator) and you are done. When the wind turns your engine, the electricity generated will be processed by the voltage stabilization circuit and stored in the battery~