Make a Wind Kinetic Power Generator first, then make a Kinetic Power Generator. Use a wrench to align surfaces that generate and require kinetic energy. The kinetic energy surface consists of four black dots. generator. Make sure to place it high
If there is no Wind Kinetic Power Generator, craft a Wind Turbine and place the rotor inside.
How to make a wind turbine in Minecraft Industry 2
Power generation process:
Wind blades --- gearbox --- motor direct current --- rectifier Bridge (polarity protection) ---- Battery
Principle:
The wind turns the blades (similar to the blades of an electric fan) to drive the gearbox so that the speed of the DC motor exceeds the Rated Speed. The voltage that will be generated on the motor will be equal to the operating voltage of the motor. Generally, 12V or 24V is selected because the battery is usually at these voltages.
Difficulty:
To make a gearbox, you must calculate the transmission ratio. For example: the rated speed of the motor is 3000, the fan blade rotates 10 times per minute, and the motor end reaches 3000 through the gearbox. At present, the gear ratio is 1:300.
The above data is obtained from the small power manual generator model I made and is for reference only. reference only.
How to make a wind turbine with 80 watt motor from a printer
Generate electricity all day (nonsense), output 0~4EU/s . How to get maximum power: Climb to the upper limit, which is the highest place, and place the generator one space below the upper limit. Do not keep any other blocks in the 9X9X7 rangeof the generator
Of course this is impossible, because you always need at least two cable blocks, so the maximum is around 3.7EU/s. PS: The transmission voltage of the new version of the tin cable has been adjusted from 3EU/t to 5EU/t, so it is possible to build high-efficiency wind power plants.
Transversal working range of the generator.
PS: The fewer things in the working range, the greater the energy output.
Wind energy generates on average 250 EU per MC day, but this is closely linked to its environment. Not only do you have to place it up high, but you also have to remove the windshield.
-Wind force: called wind force
The minimum value of wind force is 0, the maximum value is 30, it changes every 128 ticks (about 6, 4 seconds), and each change is +1 or -1 (cannot be reduced to a negative number).
If the current wind force isfrom 0 to 20, there is a 10% chance of increasing.
If the Qianfeng is between 10 and 30, there is a 10% chance of reduction.
The wind intensity reduction rate from 0 to 9 is (current wind intensity)%
The wind intensity increase probability of 21 at 30 is (current wind intensity at 30)%
The maximum safety value is 5 settings: 191 height, 2 cable blocks, no rainy days.
If the wind turbine's power value is greater than 5, there is a 0% to 0.1292% chance of damaging 0 to 4 iron ingots (broken).
Power = S *(Y - 64 - C)/750, S is the wind force, Y is the height and C is the number of cells blocked in the range 9*9*7.
When there is thunder, the electric power increases by 50% (electricity * 1.5), and when it rains, it increases by 20% (electricity * 1.2
< p>Transmit fan power via belt or e-speed changengear to the engine to turn the engine. When the motor is running, a voltage is generated at the output. The voltage generated by the motor is rectified by the rectifier diode to charge the battery or rechargeable battery.
The battery or rechargeable battery voltage should be 1-2V lower than the motor output voltage. If the battery voltage is equal to or greater than the motor output voltage, the circuit will not generate current and the battery will not be charged. If the battery voltage is too lower than the motor output voltage, the circuit may generate too strong a current, which can fry the battery or motor in severe cases.
Ordinary printer motors are usually 12V or 24V, so they can only charge 12V or 24V batteries. Batteries above 12V or 24V cannot be charged. loaded.