As we all know, waterproofing is very important, especially for top floor waterproofing project. If the waterproofing is not done well, leaks will easily occur. It will be very difficult to repair later. Some people think that the best way to waterproof the attic is to install colored steel roof tiles. In this issue, we will present the best methods for waterproofing and heat-resistant attics.
The most reliable way to waterproof the roof is to install colored steel tiles
Building a roof with colored steel tiles will solve certainly the problem of water leaks. . The best thing about the roof is the whole thing. In this way, no construction joints are left to eliminate hidden dangers, and the design plan must take into account the factors of strong wind and heavy rain.
The Best Way to Waterproof and Heat Resist the Attic
1 Commonly Used Attic Insulation Methods:
< p>1. The traditional approach is to provide a slope layer, a leveling layer, an insulation layer, a waterproof layer and a protective layer over the base layer of the roof. Before construction, the base layer of the roof must be cleaned first, and it must be flat, dry and clean; the dry-laid insulation board shall be close to the surface of the base course which is to be insulated and shall be paved and firmly padded; the joints between the upper and lower layers of the insulation board laid in layers should be offset from each other and the gaps between the boards should be tightly filled with similar materials for bonded insulation boards, the adhesive should be compatible with ; the insulating material and must be groundsecurely fixed and glued firmly.2. Water is a good heat conductor fluid. Therefore, water can also be stored on the roof for thermal insulation. The deeper the water layer, the better the thermal insulation effect. a rooftop swimming pool can also be built, which serves several purposes. It should be noted that to use a water layer for thermal insulation, the quality of the roof must be good, otherwise water leaks will occur over time in the ceiling of the top floor. Additionally, the water quality must also be good to prevent water from entering; corrode the concrete.
3. Roof insulation can be achieved by growing vegetables and fruits at home. You can directly fill the roof with soil to grow vegetables in a large area, or you can use containers to grow vegetables. It is recommended to plant leafy vines so that theThe vines cover the entire roof. Growing vegetables on the roof should be based on the bearing capacity of the roof and the crops should not corrode the concrete building.
4. Light-absorbing or reflective devices can be installed to convert sunlight shining on the roof into electrical energy or reflect it. If possible, solar panels can be installed to use sunlight to generate electricity. If it is not appropriate to use solar energy, you can install a mirror reflection array on the roof of the building. Glass, thin stainless steel plates, aluminum plates, etc. are all good reflective materials.
2. The simplest waterproofing method for the top floor:
1. The most economical method for exterior waterproofing is to apply asphalt to the exterior to create a thick layer. asphalt layer. On the roof, no matter how heavy the rain, there is no need to worry about leaks. However, asphalt is relatively rough and hard, and some small joints need to be repaired with waterproof mortar to ensure that moisture does not invade the wall. Even in winter, the waterproofing performance of asphalt roofs is excellent.
2. For interior waterproofing, you may choose to apply waterproof mortar to interior walls to seal out moisture. If the roof is flat or there is a significant accumulation of water on top, you can carry out additional waterproofing. Two-component waterproof ash grout not only has good water resistance, but also effectively resists distortion and deformation of the house due to aging.
3. For the balcony, special attention must be paid to the sealing of the joint between the window and the wall. There must be a slope on the ground, and there must be at least 2-3. cm height difference from the floor of the living room or bedroom. Set the exhaust outlet to a low level. The heart of the bathroom is the floor drain, the wall-floor connection, the pipe opening and the door stone. Brush the waterproofing onto the other parts twice. These areas should be brushed several times; First create a basin-shaped area under the door stone to form a water storage and water blocking function.
The best way to waterproof the attic is to install colored steel tiles, and the best way to waterproof and heat the attic is related to this.
The most reliable way to waterproof the roof is to install colored steel tiles
1.
This is a green and environmentally friendly method. Put more bonsai on the roof and you can grow morebonsai that you do not need maintenance. If it is easy to access the top floor and the bearing capacity of the roof is acceptable, the best insulation is to create a hanging garden, that is to say, to find earth and spread it on the roof and plant plants. If necessary, wall climbers can also be used to cover walls.
2. Lay red bricks on the roof
You can buy red bricks and lay them on the roof. It can block the sun, allow air to circulate between bricks and tiles, and also achieve a cooling effect.
3. Lay a layer of foam material on the roof.
You can lay a layer of thermal insulation material on the roof (it can also be two-in-one thermal insulation). and waterproof material), and you can also use air to isolate the principle. This method generally uses soft materialssse for thermal insulation. There are many thermal insulation materials that can be used, such as foam cement boards, foam cotton, etc. For added safety, try to choose fire-resistant materials.
4. Sunscreen and heat-insulating paint
Applying sunscreen and heat-insulating paint to the top floor can reflect the sun's rays and prevent the sun's heat from accumulating on the surface of the object .
5. Build a canopy
The advantage is that people can do activities on the roof, such as drinking tea, chatting and admiring the stars. However, the investment is relatively large. the construction is unreasonable and it will also affect the lighting.
6. Install light-absorbing or reflective devices
You can install light-absorbing or reflective devices to convert sunlight shining on the roof intoelectrical energy or reflect it. If possible, solar panels can be installed to use sunlight to generate electricity. If it is not appropriate to use solar energy, you can install a mirror reflection array on the roof of the building. Glass, thin stainless steel plates, aluminum plates, etc. are all good reflective materials.
7. Water storage for thermal insulation
Water is a good thermal conductor fluid. Therefore, water can also be stored on the roof for thermal insulation. improve the thermal insulation effect, if conditions permit. You can also build a rooftop swimming pool for multiple purposes. It should be noted that to use a water layer for thermal insulation, the quality of the roof must pass, otherwise water will seep into the ceiling over time, in addition, the quality of the water must also pass for evensure that water does not corrode the concrete;
References:
As we all know, waterproofing is very important, especially the top floor waterproofing project if waterproofing is not done. well, it will be very difficult. Leaks may occur. It will be very difficult to repair later. Some people think that the best way to waterproof the attic is to install colored steel roof tiles. In this issue, we will present the best methods for waterproofing and heat-resistant attics.
The most reliable way to waterproof the roof is to install colored steel tiles
Building a roof with colored steel tiles will solve certainly the problem of water leaks. . The best thing about the roof is the whole thing. In this wayOn, no construction joints are left to eliminate hidden dangers, and the design plan must take into account the factors of strong wind and heavy rain.
The Best Way to Waterproof and Heat Resist the Attic
1 Commonly Used Attic Insulation Methods: < /strong>
< p>1. The traditional approach is to provide a slope layer, a leveling layer, an insulation layer, a waterproof layer and a protective layer over the base layer of the roof. Before construction, the base layer of the roof must be cleaned first, and it must be flat, dry and clean; the dry-laid insulation board shall be close to the surface of the base course which is to be insulated and shall be paved and firmly padded; the joints between the upper and lower layers of the insulation board laid in layers must be offset from each other and the gaps between the layersnings should be tightly packed with similar materials for bonded insulation boards, the adhesive should be compatible with; the insulating material and must be securely fixed and glued firmly.2. Water is a good heat conductor fluid. Therefore, water can also be stored on the roof for thermal insulation. The deeper the water layer, the better the thermal insulation effect. a rooftop swimming pool can also be built, which serves several purposes. It should be noted that to use a water layer for thermal insulation, the quality of the roof must be good, otherwise water leaks will occur over time in the ceiling of the top floor. Additionally, the water quality must also be good to prevent water from entering; corrode the concrete.
3. Roof insulation can be achieved by growing vegetables and fruits at home. You can directly fill the roof with earth togrow vegetables in a large area, or you can use containers to grow vegetables. It is recommended to plant leafy vines so that the vines cover the entire roof. Growing vegetables on the roof should be based on the bearing capacity of the roof and the crops should not corrode the concrete building.
4. Light-absorbing or reflective devices can be installed to convert sunlight shining on the roof into electrical energy or reflect it. If possible, solar panels can be installed to use sunlight to generate electricity. If it is not appropriate to use solar energy, you can install a mirror reflection array on the roof of the building. Glass, thin stainless steel plates, aluminum plates, etc. are all good reflective materials.
2. The simplest waterproofing method forth top floor:
1. The most economical method for exterior waterproofing is to apply asphalt to the exterior to create a thick layer. asphalt layer. On the roof, no matter how heavy the rain, there is no need to worry about leaks. However, asphalt is relatively rough and hard, and some small joints need to be repaired with waterproof mortar to ensure that moisture does not invade the wall. Even in winter, the waterproofing performance of asphalt roofs is excellent.
2. For interior waterproofing, you may choose to apply waterproof mortar to the interior walls to seal out moisture. If the roof is flat or there is significant water accumulation on top, you may want to carry out a additional sealing work. The two-component waterproof mortar not only has good water resistance, but also effectively resists deformation and deformation of the house due to age.
3. For the balcony, particular attention must be paid to the sealing of the joint between the window and the wall. There must be a slope on the ground, and there must be at least 2-3. cm height difference from the floor of the living room or bedroom. Set the exhaust outlet to a low level. The heart of the bathroom is the floor drain, the wall-floor connection, the pipe opening and the door stone. Brush the waterproofing onto the other parts twice. These areas should be brushed several times; First create a basin-shaped area under the door stone to form a water storage and water blocking function.
The best way to waterproof the attic is to install colored steel tiles, and the best way to waterproof and heat the attic is related to this.