We have video tutorials, let's give you the text version below:
Step 1: Add water to the water tank, close the water tap first , add clean drinking water or purified water until the water tank port is in the full position, then close the water tank cover.
Step 2: Add engine oil. There are two types of engine oil, summer and winter. Please do not mix them. When adding engine oil, pay attention to the oil dipstick until oil is added to the center mark of the oil dipstick, then close the oil cap. Excess oil will cause oil discharge and oil burning, which is the case. detrimental to the machine.
Step 3: Ouyi Power diesel generator sets use independent external diesel barrels, which allows users to use oil barrels of different capacities according to theirown conditions of use. The oil inlet and oil return of the machine must be distinguished. To ensure that the oil drawn into the machine is clean, the diesel is generally left to settle for 72 hours. The oil inlet position should not be inserted at the bottom of the machine. Oil cylinder to avoid sucking dirty oil and clogging the oil pipe. Use different diesel fuel depending on the season.
Part 4: Pump the diesel, first loosen the nut of the diesel pump, hold the handle of the oil pump, then pull and press evenly until the oil enters into the oil pump. Be careful not to use excessive force.
Step 5: Purge the air, loosen the high pressure oil pump bleed screw, then press the manual oil pump. You will see oil and bubbles overflowing from the screw hole until the entire outlet is draining. see there is oil, tighten the screws.At this time, the oil pump is full of oil.
Part 6: Connect the starter and distinguish the positive and negative poles of the motor and the positive and negative poles of the battery. This is the positive pole, and the one at the end is the negative pole. . The two batteries must be connected directly in series, which can reach 24 volts. For the best effect, connect the positive pole of the motor first, do not let the terminal touch other terminals. motor pole. The terminal must be securely connected to avoid sparking and burning the terminal.
The seventh step is the pneumatic switch. Before starting the machine, or if the machine does not enter the power state, the switch must be in a separate state. The lower end of the switch is connected to the. 4 terminals. These 3 are 3 phase live wires. These are respectively V, U, W and N is the zero line. The neutral wire and any live wire aret connected to a 220V lighting power supply. Do not use one phase to exceed 1/3 of the rated power.
The eighth stage is the instrument part, the ammeter, during use, which accurately reads the power consumption. Voltmeter, check the motor output voltage, frequency meter, the frequency meter should reach 50 Hz, which is the basis for detecting the current and voltage conversion switch, the conversion switch gear can not be zero, the other gears are arbitrary. To detect the engine instrument data, the oil pressure gauge is used to detect the oil pressure of the diesel engine, at full speed, it should not be less than 0.2Mp. The tachometer should not be at 1500 rpm. exceed 100 during use. (except in plateau areas, it is best if the water does not boil), the oil temperature should generally not exceed 85 degrees.
Ninth step, start, turn on the ignition switch, press Press the button for about 5 seconds, then release it after starting the open car. If the car does not start after the first contact, it will pause for 15 seconds, start a second time and repeat the last action. Back to the car. After starting the car, run it for 30 seconds, flip the high and low speed switch, and while the machine slowly shifts from idle to high speed, check the readings of all instruments. In the initial state, the HZ counter will increase. 55HZ At this time, the V voltmeter does not display any voltage. Continue to increase the speed until the voltmeter rises between 400 V and 440 V. At this time the HZ meter will return to zero. Continue to increase the speed and the HZ meter will rise to between 50 and 52 HZ. When the voltage and speed are synchronized, it can be used normaly.
Step 10, stop the car. First turn off the air switch, turn off the power supply, adjust the diesel engine from high speed to low speed, let the machine idle for 3-5 minutes, then turn off the ignition switch. If it's winter, waterproof the tank to prevent freezing.
Did you not receive this instruction manual when you purchased it? Otherwise, ask the manufacturer or dealer.
Video tutorial on making a plastic bottle boat
Using a natural gas water heater:
1 Connect the water heater to the electrical supply. Power on, then press the switch to turn it on. Turn on the power and adjust the temperature of the water heater by adjusting it up and down. As shown in the picture:
2. After setting it up, first open the hot and cold water faucet, then open the gas faucet and the gas faucet du water heater, as shown in the picture:
3. After turning it on, the water heater will start working automatically. Generally, it will be heated quickly when we use it, it will be heated during use, and it will not be heated when we use it. not used. If you do not use it for a long time, you can turn off the gas tap, the power supply to the water heater and the hot and cold water taps.
4. When using hot water, find the water valve. Open the valve and hot water will flow.
The video tutorial on how to make a plastic bottle boat is as follows:
1. Materials: Empty plastic. a bottle of drink (bottle of mineral water), a pair of scissors, a glue gun and sticks, a knife, paint or colored paper, water and soapy water.
2. Steps: First, neckPeel off the top of the drink bottle, leaving the bottom as the shell. Next, cut a small long strip of openings at small intervals in the side of the hull to lighten the hull.
3. Use a glue gun and glue stick to glue the long openings together to form the edge of the boat. This step aims to make the hull more stable and less likely to roll.
4. Apply some soapy water to the inside of the shell, then fill the bottle with water. This step involves increasing the buoyancy of the boat, allowing the boat to float more easily on water.
5. Glue your favorite colored paper or paint to the outside of the hull to make the boat more beautiful. You can also paint a few colors inside the shell to make it more interesting.
Knowledge about beverage bottles
1. Beverage bottles are a packaging product en special plastic, usually made from plastic materials such as polyethylene or polypropylene. They are mainly used for packaging drinking water, soft drinks, juices and other liquid drinks. Beverage bottles have the characteristics of high transparency, light weight, easy transportation and long service life. Appearance design, beverage bottles also come in different shapes and specifications to meet different consumer needs and product positioning.
2. In addition to being used as packaging materials, beverage bottles can also be recycled and reused. Through recycling and processing, drinks bottles can be transformed into new plastic products again, reducing environmental pollution and wasting resources.
3. There is alsoThere are some issues that need to be paid attention to when using beverage bottles. First of all, do not place them in places subject to high temperatures or direct sunlight to avoid deformation or aging. Second, before opening the beverage bottle, you should shake the bottle or rotate the cap to avoid excessive pressure inside the bottle causing splashing or rupture. In addition, if you find that the drink bottle has a smell or changes color, you should stop using it immediately and throw it away in time.