The original Prado battery model is GS80D26L and the specification is 12V68AH. Toyota Prado battery, also called storage battery, is a type of battery. It works by converting chemical energy into electrical energy. People generally call lead-acid batteries storage batteries. That is, a battery mainly composed of lead and its oxide, and the electrolyte is a solution of sulfuric acid.
Normal battery life ranges from 1 to 8 years, which is closely related to the condition of the vehicle. Recoil of the vehicle generator is normal, the electrical appliances are not leaking and grounded, and they can basically be used for more than 3 years. If you feel that the battery cannot be charged or the starter motor is weak and the headlights are visibly dimmed, you should remove the battery and charge it with a charger for 12 to 24 hours. If it doesn't workas, the mileage has reached more than 50,000 kilometers and the generator is not defective, you should consider replacing the battery. Generally, domestic maintenance-free brands such as Sail, Zhengye and Feifei are good, and prices range from 200 yuan to 1,000 yuan depending on the battery model. Location of the Toyota Prado battery replacement tutorial: right side of the engine compartment. 1. Pull the front cover release lever on the lower left side of the main driver, then open the cover to find the battery. 2. Remove the protective cover from the battery terminals (the mounting bracket nut should also be removed). 3. Disconnect the negative terminal of the battery then remove the positive terminal. The negative electrode is connected to the car body. It is safer to remove the negative electrode first to avoid short circuits. 4. Remove all the battery retaining screws and remove the old onebattery. (Note: To prevent electrolyte from leaking, the tilt angle of the battery should not exceed 40°.) Note: Prefer the backup power replacement method (professionals only), otherwise Data stored in the dashboard will be lost and driver data will be erased. The setting parameters and driving record data are blank and settings such as date and time are reset.
Toyota Prado second insurance main items:
Toyota Prado second warranty inspection items always focus on engine oil, filter the machine, the steam filter and the air filter. Clean the ship.
Don't listen to the gummy articles from the 4S store:
Regular mineral oil should be changed every 5,000 kilometers, semi-synthetic oil about 7,000 kilometers and full synthetic oil approximately 10,000 kilometers. . Also replace the oil filter.
1. The air filter should be replaced every 5,000 to 7,000 kilometers
2. The steam filter should be replaced between 10,000 and 15,000 kilometers
3. Must be adjusted over 20,000 kilometers.
4. The throttle, fuel injector and idle motor should be cleaned once every 30,000 to 40,000 kilometers, especially the idle motor. The more you clean it, the more you love it.
5. Replace the timing belt approximately 70,000 kilometers.
6. The fourth rotation position is approximately 40,000 kilometers.
2. Other inspection items:
1. The Toyota Prado engine should be easy to start, run smoothly, have normal exhaust (exhaust gases meet standards), normal water temperature and oil pressure. meet the requirements and turn smoothly. There is no abnormal noise, the voltage of thebelt is moderate and there are no four leaks (water, oil, electricity, gas).
2. Directional freedom and toe meet requirements, the steering is light, flexible and reliable, and the front wheel does not swivel left or right. Off-road. 3. The free stroke of the clutch meets the requirements, easy to operate, complete separation, stable and reliable combination, no abnormal noise and no oil leakage in the hydraulic system.
4. Toyota Prado gearbox, engine axle, universal joint (or half shaft) transmission device, etc. Good lubrication, reliable connection, no abnormal noise or overheating, no jumping phenomenon, flexible gear shifting and no oil leakage.
5. The brake pedal free travel and braking interval meet the requirements, the driving and parking brakes are good, there is no deviation or resistance during braking, the valve proportional to inertie is working normally and there is no oil. leak.
6. Is the tire pressure normal?
7. The overhang and the shock absorber are reliably fixed and operate normally. The temperature of the wheel hub bearing should not be too high after driving.
8. Generators, starters, lights, instruments, signal lights, buttons, switches and other auxiliary equipment are complete and can work normally.
9. Add lubricating oil to all lubrication points on the vehicle.
10. Rinse and clean the entire vehicle.
One million subsidies for car purchases