Tools Required: A set of electric hot water faucet components.
1. First, install the faucet on the heating host.
2. Place the copper water inlet and power cord of the heating host into a rubber ring.
3. Insert the copper water inlet and power cord into the water pipe hole on the table.
4. Screw the mounting nut onto the copper water inlet through the undercounter cabinet to secure the heater host.
5. At this point, wrap a few circles of plastic strips around the copper water inlet to prevent water leaks.
6. Then connect the existing water pipes in the house.
7. Open the tap and see if water comes out. If water comes out, you can plug it in. The aim of this step is to avoid dry burning.
8. Insert the heating host plug into the power strip.
9. When you open the tapt, hot water comes out. It can be seen that the effect of the electric hot water faucet is good.
Detailed information:
Precautions for electric hot water faucets
1. Precautions when using for the first time
1. hot water faucet for the first time If it is a side inlet electric hot water faucet, it is recommended to clean the iron pipe with a toothbrush, and then use the pressure of tap water to discharge the dirt in the water pipe, so that the filter of the electric hot water faucet will not be easily blocked.
2. After installing the electric hot water faucet, first set the handle to the "cold water" position, then open the main valve. When you see water spouting from the hot water, plug in the power. power supply for heating, then use it later.There is no need to consider the above process and there is no need to unplug the power cord. The first time it is used is to prevent dry burning from causing the temperature limiter to cut out. power and enter the protection state.
2. Three cleaning steps
1. Do not wipe the surface of the instant hot faucet directly with a damp towel. Use a dry, soft cotton cloth to wipe it clean.
2. Do not let the instant hot faucet touch acidic and alkaline liquids. Because acidic solid substances can easily react with the paint on the surface of the instant hot water faucet, and can also easily react with the metal protected by the paint, corroding the instant hot water faucet step by step and at the same time time contaminating the cleanliness of the water flowing from the tap, contaminated water can harm our body, whether it sis used for bathing or drinking.
3. Do not wipe the instant hot faucet with burrs. ?
3. Two stages of maintenance
1. It's best not to touch it directly with your hands, because the oil on your hands can easily stick to the surface of the hot instant. faucet, making cleaning difficult.
2. You can usually spray car wax on the surface of the instant hot faucet and wipe it for 3-5 minutes. This can maintain the brightness of the instant hot faucet and at the same time protect the metal. on the surface of the hot water faucet to avoid rapid excess and empty gas undergoes oxidation reaction and causes rust.
Baidu Encyclopedia - Electric Hot Faucet
How to install an induction faucet and solve the induction faucet failure problem
How to install an induction faucet fully automatic faucet faucet in a washing machine 1. RemoveFor the water inlet pipe fittings of the fully automatic washing machine, find the end with the water inlet pipe joint, then press the slider to separate the water inlet pipe joint. water from the water inlet. pipe. 2. Place the water inlet pipe joint on the faucet, close the black washer in the faucet joint, then use a screwdriver to tighten the screw, tighten the plastic interface nut until If there are no more leaks, then connect the water inlet hose. to the water inlet connector.
Installing the sensor faucet?
1. When installing this faucet, make sure the sensor window is facing down and in one place. Distance from the bottom of the sink basin. It must be at least 25 cm, otherwise it will affect its sensitivity.
2. Close the water inlet where the sensor faucet is to be installed to ensure the faucet is installed.
3. Sortz the faucet body from the package, wrap the water inlet thread on the faucet body with leak-proof tape or glue, and screw the faucet body into the wall to install it. the water inlet hose to secure it.
4. Open the battery box cover on the protruding part of the upper cover above the sensor faucet body, carefully remove the battery box inside, and insert 4 new No. 3 alkaline batteries into the positive and negative terminals. battery terminals according to the battery instructions. At this time, the red light on the sensor window on the faucet body flashes continuously. Once the red light on the sensor window on the faucet body stops flashing, push the battery box in. the battery box and lock it. In this way, the main body of the faucet is considered installed.
5. Open the water inlet source where the robinet must be installed for testing and use the water valve knob to adjust the water flow. If there is no problem, it can be used.