Question 1: How to install solar glass tubes? Use detergent water, spray it on the tube and water tank for lubrication, put the glass tube into the water tank*** and take out a little
Then put the bottom tube of the glass tube. After the bracket is removed, the pipe can be removed.
When installing, simply insert the pipe, install the pipe bracket and adjust the position of the pipe. p>
Question 2: How to remove and install the solar glass tube. Use detergent water, spray it on the tube and water tank for lubrication, put the glass tube into the water tank*. **and remove a little
Then place the bottom tube of the glass tube. After the bracket is removed, the pipe can be removed
When installing, simply insert the pipe, install the pipe bracket and adjust the position of the pipe
Question 3: How tostretch the glass tube of the solar water heater? First, wipe down the joint between the top and the rubber? sleeve with a damp cloth several times. Once wet, put it on and it can be easily removed.
Carefully remove the remaining broken glass on the nail water tank, remove the silicone sealing ring on the water tank, clean and inspect it, and replace it if it is damaged. After installing the silicone sealing ring, take a new vacuum tube, apply lubricant (soap water, etc.) to the open end, then gently insert it into the mouth of the water tank and place the rear end into the tailstock to firmly cushion it. . You can get in the water 4 hours after sunset.
Question 4: How to install the cooked sheep alloy solar glass tube
Question 5: A broken glass tube of the solar water heater, how to instaFollow the method: Carefully remove the remaining broken glass on the hot water tank, remove the silicone sealing ring on the water tank, clean and inspect it, and replace it if damaged. After installing the silicone sealing ring, take a new vacuum tube, apply lubricant (soap water, etc.) to the open end, then gently insert it into the mouth of the water tank and place the rear end into the tailstock to firmly cushion it. . Wait 4 hours after sunset before you can turn on the water
Question 6: How to replace the broken glass tube of the solar water heater How to install the broken tube? on the water tank and remove it? Check the rubber ring and the glue. If there is no problem with the circle, take the new tube, hold the bottom of the vacuum tube and insert it evenly clockwise or counterclockwisee clockwise. The tube is higher than the base of the stand, just place the vacuum tube down. Huangming Solar is at your service. I hope it will be adopted.
Question 7: How to do it. remove the solar glass tube? First, peel off the windshield ring from the vacuum tube (glass tube) more than ten centimeters from the tube mouth. Then hold the bottom of the vacuum tube with both hands, twist the vacuum tube. left and right, and push it up; When the tail of the vacuum tube leaves the tube holder below, gently lift the vacuum tube higher than the tube holder. At this time, turn the vacuum tube left and right and pull it out. the vacuum tube downward forcefully until the vacuum tube comes out of the nozzle.
Question 8: Why can't the glass tube of the solar water heater be installed?What's happening? Check whether the installation position ist incorrect (the head and tail are interchanged, causing the installation to fail), and check whether it is caused by unequal vacuum tube specifications: there are 58*1800, 58*2100, etc. on the market, and the hole spacing is also different!
We recommend "Dr. Sun" solar energy and Sancang solar energy (no need for water level detection probes or solenoid valves). Heating and hot water usage rates are fast during rainy weather, and thereafter. the sales rate is also greatly reduced, saving time and energy. This model only takes 20-30 minutes to heat without sunlight, while the single bay solar overflow takes 2-3 hours. How to disassemble and install
If the solar water pipe is broken, it can be replaced, but if the old glass pipe is broken, you need to wear gloves to carefully remove it and clean thes glass residue before installing the new pipe. Install the dust ring. the new hose, apply detergent and water to one end of the new hose, rotate it and insert it into the bracket, and check for leaks. 1. Wear gloves and carefully remove the old broken glass pipe. rotated to reduce friction. After removing, clean the glass residue on the base and prepare a basin of detergent and water for later use. Mixing the detergent with water can reduce the resistance of the installation. , apply detergent water to the end of the new glass tube covered with the silicone ring, then align the clean water-soaked end with the circular bracket of the bottom bracket, rotate it into the base, then push it up. and the lower ends of the glass tube are inserted into the bracket, the preliminary installation is completed. Push it up and downdown to check if it is stable. If it doesn't move, remove the silicone ring and check if it is seated correctly. Check for water leakage when finished. Check for water leaks between the new glass pipe and the upper and lower seals. If there is no water leakage, install it with a dust ring. Then carefully clean the old and broken pipe. glass residue and pack it in a thick paper bag. Label it and throw it away in the designated place.
Can anyone tell me how to remove the glass tube from the solar water heater. 1. Drain everything. water from the water heater and wipe it with a clean cloth. Wipe the glass tube
2. Hold the glass tube firmly with both hands, twist it clockwise, then twist it clockwise. counterclockwise to loosen the glass tube. During the rotating processon, the sealing ring will be used, so preheat the sealing ring first, then it can be separated from the glass tube
3. The tube is loose, place the glass tube into the bucket. Insert it inside, remove the bottom part of the glass tube from the base, then slowly remove the glass tube from the bucket
4. When installing, simply follow the disassembly steps to reinstall.
First move the dust ring at the upper end of the glass tube down about 10cm, then hold the bottom of the glass tube with both hands and twist -it in one direction. After the glass tube can rotate, rotate the glass tube upwards, the bottom is separated from the bracket and the tube bracket, and the top of the glass tube is rotated downwards to separate from the ring sealing in the. water tank and disassembly is completed
Note: Use force.Do not use brute forcee or violent force in a uniform manner.
If the glass tube is damaged or cracked, it must be carefully dismantled or destroyed before cleaning