How to remove the solar glass tube
How to remove the solar glass tube Before removing the vacuum glass tube from the solar water heater, you must first take down the anti- dust (type O). rubber ring) near the water tank Apply a little water before moving to make it easier to move the dust ring.
Then hold the vacuum tube with both hands and push it upwards clockwise. When the small tail on the end of the vacuum tube exposes the exhaust pipe (the metal bracket at the bottom of the vacuum tube that holds the vacuum tube). the vacuum tube), slightly lift the lower part of the vacuum tube towards the top of the exhaust pipe.
Then grasp the vacuum tube counterclockwise and pull it down. Be sure to protect the small tail of the vacuum tube. If he hits the little tail, he will flee. If you disassemble and do notclean the vacuum tube, remember to replace the white silicone ring in the water tank, otherwise it will leak after reinserting it.
Precautions for using the equipment:
1. Due to prolonged use, the contact area between the glass tube and the bucket may rust, making the glass tube impossible to remove. It is recommended that professionals take care of this.
2. The glass tube is relatively fragile, so be careful when removing it.
3. If the solar water heater cannot be used, there may be a problem with the water inlet pipe, which can be repaired after sale.
4. Solar water heaters must be installed correctly and should be installed by professionals. If the installation location is wrong, efficient heating may not be possible.
5. Solar water heaters have a certain lifespan. If they cannot be used, it is recommended toreplace the equipment. Generally, they can be used for more than ten years.
How can the solar vacuum tube be easily removed once installed?
Solar water heater disassembly method:< /p>
Preparation materials: solar water heater, maintenance equipment
1. When disassembling, you must follow the steps. The first thing you need to specify is to turn off the power supply. Before disassembling and draining the water, you must first remember to turn off the power supply, and be sure to do this before repairs, otherwise an electric shock may occur during the disassembly process.
2. The first thing you should pay attention to when disassembling is that you must first remove the water from the insulated water tank to avoid burns from high temperature hot water during disassembly, and even if the the water in the water tank has been emptieded, it must also be left for a period of time until the temperature has completely dissipated before disassembly and maintenance can be carried out.
3. During the disassembly process, if it is not cleaned for a long time, it may be difficult to disassemble and it may even be damaged. Therefore, necessary protective measures must be taken during dismantling. Rubber gloves should be worn to avoid damage during disassembly. Scratches caused by improper operation.
4. Generally speaking, the vacuum tube of a solar water heater is the most difficult part to remove, so the vacuum tube needs to be disassembled mainly. In addition, due to water rust, etc., the vacuum tube. must be carefully turned. It should be noted that there are seals at the upper and lower ends of the vacuum tube to prevent damage and loss.
5. ApAfter removing the vacuum tube and placing it in a safe place, you can disassemble the insulated water tank, but please note that, After unscrewing the screws, two people need to work together to lift the water tank . This process is not difficult, you just need to be careful. When disassembling, the parts of the insulated water tank should be stored to avoid damage or loss.
How to remove the solar hot water pipe?
The solar thermal insulation barrel uses a silicone ring to fix the vacuum tube.
If you want to remove the vacuum tube: Take protective measures with your hands to prevent the glass tube from breaking and causing injury to you. First, pull the vacuum tube dust ring more than 20 centimeters inside the insulation barrel. Hold the vacuum tube firmly with both hands, turn it left and right, and at the same time push the vacuum tube into the directionection of. The insulation barrel, so that the end of the vacuum tube can be removed from the vacuum tube support box. Then remove the vacuum tube in the opposite direction.
Make sure to drain the water from the solar panel first. When installing the vacuum tube, remove the scale on the seal ring and the vacuum tube. Water is leaking from a wide area.
1. Drain the water from the solar water heater pipe
2. Buckle the rubber ring at the connection between the vacuum tube and the water tank
3. Buckle the rubber ring and the pipe can be removed
Detailed information:
Daily maintenance precautions of solar water heaters:
1. When installing a solar water heater, there may be a smell of dust or oil in the water pipe. When using it for the first time, you can first open the faucet to remove debris.
2. LThe water stored in the solar water heater should be discharged regularly depending on local water quality conditions. Drain time can be selected in the morning when the sensor temperature is lower.
3. The surface of the solar water heater should be wiped regularly depending on the amount of dust in the area. It can be cleaned when it rains. Keeping the water heater surface clean can get higher heat. collection efficiency.
4. When hot water is not used for several consecutive sunny days, the hot water temperature will be very high. When using the solar water heater, please turn on the cold water first, then turn on the cold water. hot water to avoid burns.
5. There is usually a filter device at the outlet end of the faucet. Scale and debris in the water line accumulate on this screen. It must be removed and cleaned regularlyto increase water flow. smooth exit.
Reference documents: Solar water heater - Baidu Encyclopedia