The reasons why solar energy does not produce water are:
1. Water cannot be discharged due to insufficient water pressure. There must be some air pressure in the solar pipe. If the air pressure is not sufficient, there will be water but it cannot be discharged. This can be fixed by adjusting the water flow or pressurizing the water. Water flow adjustment is only suitable for occasional abnormal water pressure. If the water pressure is insufficient for a long time, it is more appropriate to install a booster pump to balance the water pressure. However, it is necessary to avoid excessive water pressure. which can easily lead to problems such as burst pipes.
2. The water pipe is blocked and the water cannot be drained. Whether it's a blockage in the upper water line or a blockagege in the sewer pipe, the water will not be able to flow. However, if there is water in the solar, but it cannot be released, this is usually the case. caused by a blockage in the sewer pipe. You need to remove the sewer pipe and clean the pipe to clear the internal blockage.
3. The valve breaks down and the water cannot be drained. Another important reason why the solar water heater is not producing water is that the valve breaks down or is damaged. If it does not work, the water cannot be drained. This is usually due to aging caused by prolonged exposure to wind, sun and rain outdoors. It can be repaired and replaced in time.
Precautions for using solar energy.
1. Pay attention to the water filling time.
2. Depending on the weather conditions, determine the amount of water to ensure the appropriate water temperature during thebath.
3. Check regularly to see if the pipes, vents and other components of the water heater are working properly.
4. Flush suction hoses regularly in dry areas with heavy air pollution or strong sandstorms.
5. After the solar water heater is installed, non-professionals should not easily move, load or disassemble the entire machine to avoid damage to key components.
Why doesn't the domestic solar water heater produce water?
The reasons why the solar water heater does not produce water are: \x0d\1. The water in the water tank was emptied before it was filled with water and heated in the sun. to use. \x0d\2. The hose interface is loose or blocked, reconnect it or clear the hose. \x0d\3. In winter, water pipes can freeze. It will melt on its own about 3 hours after sunrise. In the areass cold, a drain valve can also be installed. \x0d\4. The upper and lower water valves are leaking, the water supply valve is also leaking, and the water pipe has been dry for a long time, causing water to flow back. This situation requires repair and solution. \x0d\5. The nozzle valve or hot water nozzle is malfunctioning and is not actually open, so it needs to be repaired.
1. Is the tap water pressure at the user's home lower than before?
Solution: If so, do you need to contact the water? business. Inspection of water supply lines and pressure.
2. The valve on the pipe connected to the water heater is opened smaller:
Solution: Open the water inlet valve larger.
3. Since the ground you live on is relatively high and the water pressure of the water source is low, the water flow will be even lower once the pressure is reduced by the water mixer.Solution:
Solution: At this point, it is recommended to connect a booster pump in series between the water heater water supply valve and the water inlet.
4. The mixer tap is inherently deficient and has a small diameter, and the throttling results in lower water flow:
Solution: Removable faucet inlet. Mixer end, try to connect it to the water supply valve of the water heater with a hose, or try to connect the nozzle hose directly to the hot water outlet of the water heater, and judge the quality of the water mixer depending on the water. nozzle outlet; check the pressure of the water source. If you are satisfied, simply replace the mixer with a genuine brand.
5. Improper installation, rubber ring deformation, uneven outlet pipe sealor too thin, mismatch between hose and shower head, etc. :
Solution: Select the appropriate hose and shower head according to specifications, replace the rubber ring and reinstall it.
6. The nozzle is inherently deficient and the internal resistance is large, resulting in low water flow:
Solution: Replace the nozzle.
7. The shower pipe is broken and the pipe is clogged and cannot drain water:
Solution: Use Chinese medicine to protect the water pipe during use and kinks will appear . Not only does it affect the appearance, but it is also prone to water leakage due to repeated wrinkling.