If the solar tube joint is leaking, the best way to repair it is to call a professional.
The solar tube seal is leaking. This type of professional problem should be left to the professionals. It is not cost effective to replace it directly with new solar. If the water supply pipe or sewer pipe is leaking, it is because the PPR water pipe or aluminum-plastic pipe has aged after years of exposure to wind and sun. In this case, the solar hot water pipe needs to be replaced. A valve leak means a valve failure. In this case, a new solar valve or solenoid valve must be replaced.
If the position of the electric heater of the solar heating tube is leaking, it means that the electric heater is rusty and damaged, and a new sealing ring or electric heating rod needs to be replaced. Water leaks from solar vacuum tubee are basically caused by the aging of the solar silicone ring, and the vacuum tube needs to be removed and replaced with a new silicone ring. Water leaks from the solar exhaust outlet are usually caused by damaged sensors or meters. In this case, the water temperature and level meter or a new solar meter must be replaced.
How Solar Water Heaters Work
Solar water heaters use evacuated collector tubes to absorb heat from the sun and transfer it to the cold water, thus allowing it to be converted into hot water. Because there are usually vacuum collector tubes installed inside solar water heaters, when sunlight shines on the solar water heater, the internal vacuum collector tubes absorb all the heat from the light from the solar water heater. sun and transfer the heat to the cold water in the tube. turns intohot water, then the hot water flows down the glass tube into the water tank where the hot water can be stored.
The internal working system of the solar water heater is fully automatic and does not require regular monitoring or maintenance by the user. It is not prone to contamination or leaks, and is very environmentally friendly and safe. And there is usually a water tank inside which can store hot water. The water tank has good insulation effect and large water storage capacity, so users can have hot water at any time without waiting.
How to replace the 20 silicone ring of the solar water heater
Each has its own advantages I recommend using a silicone ring for better sealing.
The upper and lower water pipes are welded, which can basically eliminate the possibility of water leakageu. You can use it with confidence. If there is a problem with the water heater, it will be inconvenient and difficult to resolve. disassemble. It is best to use a silicone ring to seal it, which is easy to disassemble and repair.
How to replace the silicone solar pad
Push the solar tube up to separate the bottom part from the base, then pull it down and remove it. Be careful not to drop the bottom. The piece looks like a small glass in a thermos bottle. If the column is damaged, it may not be insulated. Remove the silicone ring and replace it, press it in the opposite direction and you will be fine. When installing, apply a little soapy water to the glass column, which will be more convenient.
Attach the ring. new seal with cotton thread. Do not tie it, connect the large coiled wire end to end, then place the new joint into the water tank withec your fingers, then use a small stick to push in the new joint and stretch the wire. Once the seal is in place, cut the cotton thread, remove the cotton thread inside and clean it with a clean product. Stain the semen on the 4 minute pipe and slide the water pipe into the water tank. Or add a circle of grooves on the solar silicone pad When you place it, first fix a small edge of the silicone pad with the inner tank of the water tank, then tighten it little by little clockwise. The steps are as follows:
1. Drain the water to avoid burns and water leaks
2. Remove the pipes and other objects outside the broken silicone ring. Prevent various materials from scratching your hands?
3. Buy a new one and install it
4. Fill the water and pay attention to the time
(1) Silicone pad features:
1. High reliability
2. High compressibility, soft and elastic
3. Low thermal conductivity
>4, Natural adhesion, no need for additional surface adhesive
5. Meets ROHS, SGS and UL certification environmental requirements
6. Multiple color options, bright colors, customizable shapes. .
7. The raw materials are 100% environmentally friendly food grade silica gel.
8. Low carbon and environmentally friendly, non-toxic and odorless, soft, non-slip, shockproof, waterproof, heat insulating, not easy to age, not easy to fade and easy to fade. to clean.
9. Durable and effectively protects the furniture surface from burns and scratches.
10. Temperature resistance range: -40 ~ 230 degrees Celsius. It remains soft and does not deform even when cooked or frozen.
11. Some silicone pads must meet the standard of yourt of US FDA food grade: 21CFR177.2600.
(2) Objective:
1. Filling between the circuit board and the heat sink
2. Filling between the integrated circuit and the heat sink or product shell
3. Filling between IC and similar heat dissipation materials (such as metal shields)
4. As a buffer for machine connections in industry, it is friction-resistant and sealed.
(Data source: Baidu Encyclopedia: Silicone stamp)