Taiwan The solution to the problem of removing water from solar energy is as follows
1 The solar energy vacuum tube. is damaged. For this reason it is necessary to replace the suction pipe.
2. Sewer pipes, valves or joints are leaking and the sewer pipes need to be repaired.
3. The tap water pressure is too high and hot water cannot flow. The flow of tap water should be reduced.
4. The solar water heater has multiple water outlets and there is a phenomenon of water leakage. It is necessary to install an independent valve and close the valve.
5. If a fully automatic auxiliary water tank is installed, the auxiliary water tank float valve may not be closed properly or may fail, resulting in continuous replenishment of cold water and a drop in water temperature. In thisIn this case, the float valve and associated parts must be replaced.
Solar water heater maintenance methods
1. If you want to extend the life of solar energy, you must use solar water heaters correctly in your life. , especially when going on the water, it is best not to go on the water when the sun is shining during the day, and be careful not to let the solar power work when there is no water.
2. The solar water tank should be well protected to prevent the exhaust hole of the solar water tank from being blocked. Do not install other auxiliary tools by yourself. water tank from time to time. Check and resolve any issues quickly.
3. Do not place any objects around the solar power to avoid damage to the solar vacuum tube due to natural factors. After installation, solar energy cannot be moved or rebuilt.installed casually.
When the Sanle solar water heater is filled with water, what is the problem with the overflow pipe leaking?
There is one port too many -full at the high water level of the solar water heater. , and the overflow port is connected to the overflow pipe. The overflow pipe has two functions. One is to provide ventilation to ensure that the pressure in the solar water storage tank will not increase due to feed water pressure. The other is to ensure that the water level in the water storage tank reaches the overflow. Opening and excess water will drain from the overflow opening. When the overflow pipe overflows with water, it means the solar water heater is full of water. At this time, the water supply valve should be closed in time to avoid wasting water resources. . When filling with water, it is normal for a small amount of water to flow outfrom the overflow pipe because the very humid air inside the tank is continually exhausted from the overflow pipe.
What happens when the solar water heater is not full and water flows from the overflow pipe?Under normal circumstances, the overflow pipe will not overflow until the water is full if the water overflows before the water. is full, it may be due to the overflow pipe. This is caused by poor or damaged sealing of the port, or the water is really full and overflowing, but the instrument incorrectly detects and shows that it is not full. At that point you need to check. the water level probe and the instrument as well as the connection lines between them
I hope to adopt and thank you
Why is there no hot water in Sanle solar water heaterHow to use solar? water heater. When using the solar water heater, interested people will find that if the lead timeWater supply and water quantity are intelligently organized, this will result in double the result with half the effort. Users who are just starting out may not be sure. Over time, you will slowly understand the experience and the rules.
Tips for using solar water heaters:
A. When taking a bath, if the water in the solar water heater is used up and the person does not is not rinsed, you can run cold water for a few minutes, using the principle that cold water flows and hot water floats, you can take a bath by taking out the hot water from the vacuum tube .
B. Using the principle of A, if there is still some hot water left in the solar water heater after taking a bath and cold water is applied for a few minutes , hot water can be used to wash one more person. (Each vacuum tube produces 6.5 liters or 8 liters of hot waterde)
C. Determine the amount of water supplied based on the weather forecast to obtain a more satisfactory water temperature: if the weather is good, the water can be filled to the top , if it is cloudy or cloudy. If it rains, the water in the tank will be filled with half a tank of water; if it rains, the original water will be retained and no cold water will be poured.
D. After taking a shower at night, if there is still half of the hot water close to 70℃ in the water heater tank, in order to avoid excessive heat loss (the less water, the faster heat loss), you should also adjust the temperature according to the weather. The forecast determines the amount of water supplied. On clear days, the water supply will be full, and on cloudy and rainy days, 2/3 of the water supply will be. completed.
E. The role of the auxiliary water tank: the auxiliary water tank mainly servesent areas with a regular water supply and unstable water pressure. The water storage capacity is between 1/2 and 3 times that of solar water. water heater. It is installed on the roof of the building. The main function is to mix cold water with water to adjust the water temperature when bathing. In addition, it can be used as a water storage tank when the water is turned off and can also precipitate impurities in the water in areas without tap water. .
F. Hot and cold water adjustment: The steps for adjusting the water temperature of the solar water heater are as follows: first open the cold water valve, adjust the cold water flow appropriately, then open the hot water valve. adjust until the desired bath temperature is obtained. Additionally, the amount of cold water can be determined empirically based on weather conditions. Be careful not to point at the drinktowards the human body to avoid burns.
G. Wind resistance measurements: Since the components of the solar water heater are reliably connected, the wind resistance performance mainly depends on its installation and fixing method. Currently, Huangming uses 8# and galvanized iron wire. Extended expansion bolts for mounting, front and rear. It forms an eight shape and has good wind resistance. In addition, in areas with strong winds such as coastal areas, the effect will be better if the support structure is changed. the back plate is removed and secured with steel strands used to secure telephone poles.
H. How to extend the service life: In order to extend the service life of the solar water heater, users should pay attention to the following points during use:
1 . After the water heater is installed and fixed, non-professional personnelionnel should not move or disassemble easily to avoid damage to key components.
2. There should be no debris around the water heater to eliminate the hidden danger of hitting the vacuum tube.
3. Check the exhaust hole regularly to ensure that it is smooth to avoid inflation or deflation of the water tank.
4. When cleaning the vacuum tube regularly, be careful not to damage the tip of the vacuum tube.
5. In winter, the pipes should be prevented from freezing and cracking, and the exhaust pipe should be kept clear.
6. Solar water heaters equipped with auxiliary electric heating devices should pay special attention to water supply to avoid unnecessary trouble.Boil the water dry.
Sanle solar water heater