Solar water heaters will produce dirt after prolonged use. If they are not cleaned, it will not only affect the water quality, but also the lifespan of the solar water heater. So, what are the cleaning methods for solar water heaters? PChouse will guide you through this.
1. Use professional solar descaler for cleaning: buy special solar descaler, open the water inlet of the solar water heater, add the descaler into the water tank, and let the solar energy cycle automatically for 30 minutes. minutes. At this time, the descaling liquid will penetrate all parts of the water heater evenly. Then open the drain outlet and drain the water. Finally, add water and cycle for two minutes. Once the water is drained, the scale can be completely removed.
2. Use white vinegar to clean: first drain all the water from the sola water heaterire, then remove all vacuum tubes, pour appropriate amount of white vinegar into the vacuum tubes, soak for about 10 minutes. , then use a brush to clean it. Just scrub twice with clean water. But be sure to handle it with care, as vacuum tubes are very fragile.
How to remove scale from solar energy
Solar water heaters generally need to be cleaned, inspected and disinfected every one and a half to two years. You can ask professionals. to clean them, or you can do it yourself. Get your hands dirty and disinfect them.
Cleaning the solar water heater:
Remove the solar vacuum tube, fill it with appropriate amount of white vinegar and soak it for 10 minutes, then use a brush it out and forward to remove the remaining scale, and simply pass clean water on both sides. Butbe sure to handle it with care, as vacuum tubes are very fragile.
If it is inconvenient to remove the vacuum tube, you can open the water inlet of the solar water heater and pour white vinegar into the water storage tank. Allow the water heater to circulate automatically for 20 to 30 minutes to allow the white vinegar to fully contact all parts, then open the drain and drain the white vinegar that cleaned the scale. Finally, fill the water tank with water and circulate it again for 2 minutes, then drain the circulating water.
Buy a special solar descaler, mix it with water in a ratio of 1:10 and add the cleaning solution to the water tank. If the water heater in the house has not been cleaned for a long time, you can also pour the original solution directly into it and let it soak for 5 to 15 minutes to disintegrate the scale.Let it cycle automatically for 20 to 30 minutes, then drain the cleaning fluid directly from the drain. .Turn on the water supply, fill it with water then circulate it for two minutes, then drain it and that's it.
Detailed information:
The heat absorption process of solar water heater relies on the vacuum tube to radiate sunlight to absorb heat. The heat collected coating transfers heat into the water along the tube wall. . This helps absorb heat. Once the water temperature rises, hot water rises and cold water falls, forming an upward force. After continuous circulation, a thermal alternation effect is obtained.
Domestic solar water heaters operate according to natural circulation, without anyother force interference. It is a passThe work done by the gravity of superheated water does not need to take into account the loss of thermal energy and pipe circulation is generally not used.
The usage process involves the top water operation method of solar water heater, using a casing or coil to operate. When installing, the height requirements of the installation should be taken into account so that it is more convenient to use and maintain the water supply capacity.
References:
No matter where solar energy is used, there will be scale problems. Under normal circumstances, tartar should be removed once a year. Otherwise, the temperature of. solar power won't be as good as everyyear. For one year, if the water quality is poor in some areas, do not choose a three-cavity pipe (pipe-in-tube). Currently, there are three methods of anti-solar. -Scaling and descaling:
(1) Add descaling agent during installation. Magnesium rod with scale function. But it has no effect. Even the magnesium rod itself will be chalky. There is no difference between installation and non-installation. .
(2) Simply add a descaling agent. I do not recommend this method. General descaling agents are acidic or alkali, which will corrode the inner tank of the water tank, and the scale in the vacuum tube cannot. be removed. You should remove the hose after 24 hours and empty the dirt.
(3) Physical descaling method. This involves unplugging the vacuum tube and drying it in the sun for two days, then installing it. Before installing the tube, pour waterinto the solar panel inside to remove the. scale in the water tank. This method will not cause damage to solar energy, save money and completely eliminate scale.