It is better to choose a cloudy day when you want to disassemble the solar tube. First, drain all the water from the solar panel. Start by removing the first tube from the solar side and attach the rubber ring at the connection. between the vacuum tube and the water tank. Hold both ends of the vacuum tube with both hands, twist it left and right to remove the vacuum tube from the base, and then remove it while rotating it.
From a safety point of view, it is better to hire professionals to disassemble solar tubes, because some solar tubes that have been used for a long time are difficult to disassemble safely. When dismantling the solar tubes, you cannot choose a weather with strong sunshine, because when dismantling the solar tubes, you need to drain all the water from the solar panels. If the sun is too strong and there is no water in the tubes, the strong light from the ssun will do it. shorten the life of vacuum tubes, or even damage the vacuum tube.
When disassembling the solar tube, it is best to use water soaked in detergent or lye to lubricate the vacuum tube. Remove the rubber ring between the vacuum tube and the water tank, then hold the vacuum tube with it. with both hands and use a little force to remove the other end of the vacuum tube. Remove one end of the circlip, then gently remove the vacuum tube from the water tank. During the disassembly process, you should not use too much force, otherwise the solar tube may burst and cause injury to people. Therefore, non-professionals should pay attention to safety when disassembling the solar tube.
During the process of disassembling the solar tube, if the rubber ring cannot rotate for a long time, you can use dishwashing liquid to apply to the contact area betweenthe tube and the silicone ring to increase lubrication, then apply it to the rubber ring. When disassembling the solar tube, it is best to disassemble it from the first tube on the solar side, which will make the operation easier.
How to disassemble and assemble a solar water heater
First disconnect the power supply, close the water supply tap, go to the roof, open the drain of the wastewater to let the water flow. , or disconnect a few pipes, prepare before removing the pipes 2 bottles of mineral water, fill them with water, add a little detergent for lubrication, drill a few holes in the lid, spray water on the tube to lubricate it, so the glass tube can be easily removed, and pull the sealing ring down for some movement. Twist the hose several times and insert it a little into the water tank, so that there is space underneath to remove facthe pipe. Place the pipes in place. Place the 6 pipes in a triangle and use a wide transparent tape. Tie the tape at both ends for easy transportation. Use pipe scissors to directly cut pipes, wires and signal wires (be sure to unplug). power supply). Cut off any water lines and wires entering the room beforehand, and simply remove the pipes. You can use a little violence (if you keep it, water will flow out the flue when it rains). , then remove the water tank from the shelf and simply carry the rest downstairs. The shelf can be removed or not, it depends on the specific situation. The following points should be noted when disassembling and reassembling. solar water heater: 1. Turn off the water source and power supply: Before disassembly and assembly, the water source and power supply of the floor water heaterarea must be turned off to avoid accidents. 2. Drain the water: Before disassembly and assembly, the water of the solar water heater should be drained to prevent water from flowing out during disassembly. 3. Disassemble the pipes: When disassembling the solar water heater, you must first disassemble the pipes and remove the water pipes and wires. 4. Remove the bracket: RemoveWhen removing the solar water heater, you must first disassemble the bracket and remove the solar water heater from the bracket. 5. Disassemble the solar collector: If you need to disassemble the solar collector, you must first remove the sensor screws and remove the sensor from the solar water heater. 6. Installation: Once disassembly is completed, the solar water heater needs to be reinstalled. Just follow the reverse steps. It should be noted that safety should be considered during the disassembly and installation process to avoid accidents. If you are unsure of the method of fonoperation, it is recommended to call on professionals for disassembly and assembly.