The installation and removal methods of solar tubes are as follows:
Tools: SANGGAOXSY-24 solar water heater, gloves, dish soap , bucket.
1. First, drain the water from the solar water heater pipe.
2. Then wear gloves and buckle the rubber ring at the connection between the vacuum tube and the water tank.
3. Buckle the rubber ring and the tube can be removed.
4. When installing, you should first apply a little dishwashing liquid to the installation part of the pipe to lubricate the installation.
5. Then aim for the hole at the top of the water, gently rotate and push up.
6. Push it forward about 15 centimeters, aim at the bottom, rotate it slightly and remove it.
7. Slowly put it into the bottom, as shown in the picture below, the installation is successful.
How to solve the man escaperubber chon of the solar pipe? Thanks
The reason for the leak is that when you installed the vacuum tube, you pushed the sealing ring crooked and even pushed it into the water tank.
This equates to no sealing, it would be strange if it didn't leak.
It is recommended when installing the vacuum tube to first apply detergent solution to the seal ring and insulating layer (just pour the detergent into the water), then Also apply detergent to the vacuum tube solution.
Not only does this save effort during installation, but it also prevents the sealing ring from being pushed into the water tank due to excessive friction, rather than being stuck on the inner hole of the tank.
Silicone ring leaks are usually caused by the aging or deformation of the silicone ring and the sealing is not good.t not waterproof. In this case, the only option is to replace the silicone ring. It is recommended to contact the manufacturer's after-sales personnel. If it is under warranty, it must be replaced free of charge within the period.
If the warranty period is expired, maintenance fees should be charged.
There is a rubber ring called silicone ring at the junction of the solar vacuum tube and the water tank, which is used for sealing and has high temperature resistance. When installing, look at the socket first. water tank collector tube (vacuum tube) - The holes of the vacuum tube and the stainless steel edges of the holes of the vacuum tube are smaller than the holes of the insulation layer.
Hold the silicone ring sideways and look at the edge. There is a groove in the middle of the silicone ring. On both sides of the groove, one side should be thicker and the outer circle larger, and the. the other side devwould be thinner and smaller. The side with the thinner side and smaller outer circle faces inward when placed at the water tank suction pipe hole. The groove should be completely closed with the stainless steel hole visible at the mouth of the water tank suction pipe.
When installing, first install one side little by little. It's like installing a bicycle tire. The installed silicone ring should look like the silicone ring in your hand, then the silicone ring is installed. Then it's time to intubate. When intubating, first wet the windshield (usually a black rubber ring between the vacuum tube and the outer wall of the water tank) with clean water and place it over the extremity open top of the vacuum tube.
Wet the installed silicone ring with laundry detergent or add water to the solar panel to let the water flow out.u vacuum tube hole.
At this time, hold the tail of the vacuum tube with one hand to protect the tip of the tail, and hold it 1/3 of the vacuum tube, the force should be uniform and the direction of the force should be consistent with the coaxial line of the tube mouth. Insert the vacuum tube into the vacuum tube hole of the water tank. you can insert an extra section, then remove it after the tail of the vacuum tube is aligned with the protective bracket, until the vacuum tube and the protective bracket are firmly fixed, then put the ring windshield firmly against the exterior wall. of the water tank.
Detailed information:
Solar water heater cleaning steps: If you suitable, you can remove the vacuum tube, fill it with appropriate amount of white vinegar and soak it for 10 minutes, then use a brush to pull it back and forthback to remove the remaining scale and rinse it twice with clean water.
1. If it is inconvenient to remove the vacuum tube, you can open the water inlet of the solar water heater and add white vinegar to the water tank.
2. Automatically heat for 20-30 minutes to completely contact all parts with the white vinegar solution, then open the drain and drain the white vinegar that cleaned the scale.
3. Fill the water tank with water and then circulate it for 2 minutes, then drain the circulating water, and the cleaning and descaling work is completed.
4. Due to chemical reactions, vacuum tubes soaked in white vinegar or washed with circulation methods will have an unpleasant odor. After cleaning, you can use lemon juice to scrub it or add some during circulation. can be used to remove flavor.
Reference materials:
Baidu Encyclopedia of Solar Energy