With the advancement and development of science and technology, solar energy becomes more and more intelligent, and its lifespan is continuously extended. Once installed, solar power can operate intelligently and autonomously, without requiring manual operation or maintenance. The water supply can be adjusted automatically within a day, and some can even intelligently assist with heating. Whether it's sunny or not, even on rainy or snowy days, you will have hot water when you get home from work. You will be able to use it as soon as you turn it on. You won't need to wait long anymore. , which makes people's lives more convenient. Solar racks are definitely essential for solar energy installation. Solar racks are an important supporting element of solar water tanks. They constitute another major component of solar energy afterwater tanks and water pipes. They also play a very important role in promoting solar energy. . This article will give you a detailed explanation on installing solar racks.
In some coastal areas where the daily winds are strong, consumers will pay special attention to the design of the solar water heater having strong wind resistance when purchasing a solar water heater domestic. If the quality of the solar water heater is high, most of its solar brackets are made of aluminum alloy brackets because they are thick and strong.
When positioning during construction, it should be ensured that the front and rear pillars of the steel pile are on the same straight line, and the straight line formed by the front and rear pillars should be formed with the front. and the rear pillars respectively. The two straight lines are perpendicular. Moreover, the straight line ne should not be bent and the bending range should be less than 2mm. The height of steel piles also has corresponding requirements, and the height of the tallest part should be at the same level. The distance between the adjacent foundation centers of the front and rear pillars of the steel piles is about 3 meters, and the distance between the front and rear pillars is about 2 meters.
The center of the welded plate on the upper edge of the front pillar must be at the same level. The front pillar can be fixed after reserving the corresponding length in the steel pile. ?Determine the approximate installation angle according to the inclination required by the drawing, and at the same time ensure that the center of the welded plate on the upper edge of the rear pillar is consistent in height. The rear pillar can also be fixed after reservation. the length in the steel pile. Once the front and rear uprights are fixed, it isimportant to install the longitudinal beam on the connecting plate. The center line of the longitudinal beam must coincide with the center line of the front and rear uprights. Next comes the installation of the guyed reinforcement: one end of the guyed reinforcement is connected to the longitudinal beam, and the other end is connected to the pillar with a hoop. The longitudinal beams must be parallel to each other.
Installing solar supports is not difficult. During installation, components must be assembled according to the instructions or design drawings. Use a wrench to tighten the screws with the appropriate force. Remember to install the rear braces last.
Consumers usually install solar water heaters on the roof, facing north and south, preferably about 5 to 10 degrees from south to west, because this direction is conducive to bright light. solar released and can increase the duration of ensunshine. After reading this, do you think it's simple enough?
Tubatu Online brings you “every decorating quote, 1-4 local decorating companies, 3 sets of decorating design plans” and decorating avoidance strategies for free! Click this link: https://www.to8to.com/yezhu/zxbj-cszy.php?to8to_from=seo_zhidao_m_jiare&wb, you can get it for free~
How big is the solar support Strap
1.5 meters.
The height of the solar water heater bracket is determined based on the size and installation location of the solar water heater. The height of the solar water heater support from the ground is 1.5 meters. This height can ensure that the solar water heater can receive enough sunlight after installation and improve the efficiency of the water heater.
How many screws are used to attach the purlin wall bracketto solar?
The dimensions of the Sanle solar rack are: 1550 mm long, 43 mm wide and 1.5 mm thick. According to Sanle official website, the size of the solar mount is 1550*43*1.5mm. Sanle solar brackets are made of aluminum alloy and other materials. They have excellent oxidation resistance, corrosion resistance, light weight and high strength. They are simple and practical to install. roofs, floors, water surfaces, etc. Occasionally, it is used for the installation and fixing of solar panels to maximize the use of solar energy, reduce the use of traditional energy and is environmentally friendly, economical and safe.
The solar panel wall bracket is fixed with screws with a diameter of 6 mm and a length of 20 mm. According to Tubatu Decoration Network, solar panel wall brackets should use expansion bolts with a diameter of 6mm and a length of 20 mm to be stable. Solar panel brackets are product components supplied by solar bracket factories for solar companies. According to the purpose of the rack, they can be divided into solar thermal racks (solar water heater racks) and solar photovoltaic racks.