When removing the solar hot water pipe, pay attention to choosing the appropriate time to avoid burns during disassembly. At the same time, you can also use dish soap to lubricate the heating tube to avoid accidents caused by violent pulling. The following is a detailed explanation of the disassembly steps.
/
Tips: Before removing the heating pipe, you can open the water supply of the solar water heater, add white vinegar or descaler to the tank of water, then fill it with water and start the automatic heating cycle 20 minutes, then drain the water to remove scale and extend the life of the pipe.
1. First, choose a suitable time. It is better to be in cloudy weather, and the best time is when the sun is not strong (morning or evening), because before dismantling, all the water in the solar water heater should be drained to avoid thewater leaks in the pipe. and cause burns.
2. Before disassembling the heating tube, it is best to lubricate the heating tube with lye-soaked water. The heating tube should also be pulled gently. If pulled hard, the vacuum tube may burst and injure someone.
3. There is an apron at the connection between the heating pipe and the water tank. If the apron is very tight, you can scald it with hot water first, and then slowly remove the apron, or you can do it. You can wash it with water. Use dish soap to lubricate the gap between the heating tube and the rubber ring for easy removal.
4. After removing the heating tube, it is recommended to put it in a special carton to avoid impact damage during transportation.
How to remove the heating pipe from the solar water heater?
The disassembly and assembly ofSolar water heaters require certain skills and precautions. Here are the general steps for disassembly and assembly of solar water heaters:
Disassembly of solar water heaters:
Turn off the water heater: First of all, make sure that the hot water supply to the solar water heater is turned off. You can close the valve connected to the water heater or turn off the power to the water heater.
Drain the water heater: Open the water heater drain valve and completely drain the water from the water heater. This step aims to reduce weight during disassembly and prevent water leaks.
Disconnect the water pipe: Use a wrench or other suitable tool to gently loosen the connection between the solar water heater and the water pipe. This usually includes the inlet and outlet pipes.
Disconnect the power source (if applicable): If the solar water heater is running on an electrical source, make sure the powertation is cut and the electrical connection is disconnected.
Remove the mounting bolts: Check the mounting bolts or brackets of the solar water heater, use suitable tools to loosen and remove them.
Lift the water heater carefully: Lift the solar water heater carefully to ensure that it is not damaged or bumped during transportation.
Installing a solar water heater:
Prepare the installation location: Choose a suitable location to install the solar water heater and ensure that the support or the fixture is firm and reliable.
Install the fixing bolts: According to the design and requirements of the solar water heater, install the fixing bolts or brackets in the predetermined position.
Connect the water pipes: Connect the water inlet pipe and the water outlet pipe, making sure the connection is tight and securethat. If necessary, use a suitable sealing material, e.g. sealing tape or pipe putty.
Connect to a power source (if applicable): If your solar water heater requires a power source, make sure it is properly connected and perform all safety checks. necessary security.
Water Filling: Open the water inlet valve and inject water into the solar water heater system. Make sure the water is circulating properly and check for leaks.
How to disassemble the heating pipe of the solar water heater:
1. First of all, it is better to choose a cloudy day, in the morning or evening. , because before disassembly, you must first drain all the hot water from the solar water heater to avoid being burned by the hot water seeping out when removing the pipe. If it is noon at this time, since the water in the vacuum tube has emitted light, the strong luDirect sunlight will damage the vacuum tube and shorten its service life.
2. When disassembling, it is best to use water soaked in detergent or washing powder to lubricate the vacuum tube. At the same time, pay attention to the angle of the vacuum tube and avoid it. pull the angle to prevent the vacuum tube from bursting. After disassembly, the vacuum tube must be packed in special polyester foam compartments and placed in special cartons to avoid shock during transportation.
3. Use water soaked in detergent or washing powder to lubricate the connection between the vacuum tube and the water tank, then turn it left and right and press it in lightly, then remove the other end of the Remove the vacuum tube of the circlip. Carefully remove the vacuum tube from the tank.
Detailed information:
Solar water heater leak repair
1. Leaking water tank
Solar insulation The fWater leaks are relatively rare. If upon inspection it is found that the water tank liner is indeed leaking, then you should consider replacing the solar water tank. The quality and age of the water tank coating directly causes the water tank to rust and leak. But in general, the solar seal ring is usually damaged. In this case, just ask the master to come and replace a few silicone solar rings.
2. Water pipe leak
If the water pipe is leaking or the water pipe is leaking, it is because the PPR water pipe or aluminum-plastic pipe has aged after years of wind. and exposure to the sun. This situation It is necessary to replace the solar hot water pipe. A valve leak means a valve failure. In this case, a new solar valve or solenoid valve must be replaced.
3. Solar heating pipe is leaking
If the solar heating pipe leaks from the electric heater position, it means that the electric heater is rusty and damaged, and a new seal or the electric heating rod needs to be replaced. Water leakage of the solar vacuum tube is basically caused by the aging of the solar silicone ring, and the vacuum tube needs to be removed and replaced with a new silicone ring. Water leaks from the solar exhaust outlet are usually caused by damaged sensors or meters. In this case, the water temperature and level meter or a new solar meter must be replaced.
Reference documents:
Baidu Encyclopedia - Solar water heater