After installing the solar water heater bracket and water tank, pay attention to the following steps:
1. Use a wrench to fix the bolts and nuts of the solar water heater bracket and shake it gently. by hand to avoid any deformation;
2. The water tank and bracket are secured with four bolts. Simply tighten the nuts by hand. Do not tighten them to make it easier to rotate the water tank.
3. Prepare half a bowl of water, pour in a spoonful of dish soap or laundry detergent, stir and set aside
4. the tube into the detergent in the basin. Essential water (lubricating effect), insert the tube mouth into the vacuum tube jack on the side of the solar water tank, and put the tube tail back into the solar tail stock. installed;
5. Rotate and adjust the water tank, make sure the vacuum tube and vacuum tube hole on the solar water tank shell arealigned to prevent the water tank shell from crushing the vacuum tube;< /p>
6. Repair the solar water tank. That is, tighten the four bolts that secure the water tank and the bracket;
7. Insert the other vacuum tubes into the solar water tank according to the fourth item.
8. After checking the vacuum tube, immediately apply cold water or wait until the sun goes down before applying water to avoid exploding the vacuum tube.
Of course, if the cold water hose has been connected, you can also insert the hose while filling the water, so you do not need dishwashing liquid. For initial installation, follow the method above.
How to install solar vacuum tubes? Please ask for installation steps
Yes.
Flat solar panels and evacuated tube solar panels can be installed together and provide multiple benefitsntages. Solar energy from flat panels is mainly responsible for absorbing solar energy and converting it into thermal energy, while solar energy from vacuum tubes is responsible for collecting heat. By combining the two, the functions of heat capture and insulation can be achieved at the same time. Flat solar panels feature strong materials, usually metal, that make them more resistant to harsh environmental conditions, such as wind and rain. This makes flat solar panels more reliable and durable when installed and used outdoors. Vacuum tube solar power has higher thermal efficiency and can absorb solar energy more efficiently and convert it into thermal energy. The vacuum layer inside the vacuum tube can provide good thermal insulation effect and reduce heat loss, thereby improving the use efficiency.lization of heat from the system.
What are the installation steps of indoor solar pipes
The installation steps are as follows:
1
Wet the windshield with clean water. Place it on the top end of the vacuum tube and expose the port. Hold the tail of the tube with one hand to protect the tip of the tail with the other hand. and keep the force direction coaxial with the tube mouth. In the same way, insert the vacuum tube into the vacuum tube hole of the water tank. At this time you can insert an additional section after the tail of the tube. The vacuum tube is aligned with the protective bracket, remove it until the vacuum tube and the protective bracket are firmly fixed, then place the windshield ring firmly against the outer wall of the tank. water, the first vacuum tube is installed.
2. Follow the steps above to install all vacuum tubes in orderand from one side to the other.
Installation of direct plug vacuum tubes for solar water heatersWhat is the method?
1. Installing the pipe support. First install the vacuum tube bracket, install the lower part of the collector tube, and install the tube bracket in the bracket position.
2. First check the silicone sealing ring covering the insulated water tank liner, then check whether the rear corner of the vacuum tube is damaged, then check the transparency of the mercury-type liner and check if there is burrs and roundness at the tube level. mouth. Insert the outer rubber sealing ring of the vacuum tube about 15cm into the vacuum tube, wet the mouth of the tube completely with soapy water, and hold the rear end of the vacuum tube with your right hand. One is to protect the back corner of. the process, and the other is to facilitate intubation. Insert the tubevacuum vertically to the nozzle, push it into the water tank with uniform force and smooth rotation, then flip the tube seat after insertion, completing the installation of all vacuum tubes in sequence .
2. Connect the hot and cold water pipes
1. Wrap the tape around the water inlet and outlet, then install the pipe fittings and connect them to the special solar pipes;< /p>
2. Electric heating tape Close to the outer wall of the pipe and tie it tightly with a sticky tie;
3. Install the sensor into the water level gauge hole of the water tank. shopping center and use thick polyethylene rubber plastic pipe for insulation outside the pipe;
4. The water supplied to the solar water tank is connected to tap water.
After installing the solar water heater bracket and water tank, pay attention to the following stepsantes:
1. Use a wrench to fix the bolts and nuts of the solar water heater bracket, and shake it gently by hand to avoid deformation;
p>
2. The water tank and bracket are secured with four bolts. Simply tighten the nuts by hand. space to facilitate the rotation of the water tank.
3. Prepare half a bowl of water, pour in a spoonful of dish soap or laundry detergent, stir and set aside
4. the tube into the detergent in the basin. Essential water (lubricating effect), insert the tube mouth into the vacuum tube jack on the side of the solar water tank, and put the tube tail back into the solar tail stock. installed;
5. Rotate and adjust the water tank, ensure that the vacuum tube and the vacuum tube hole on the solar water tank shell are aligned to prevent the water tank shell from crushing the tube empty;< /p>
6. Repair the sola water tankire. That is, tighten the four bolts that secure the water tank and the bracket;
7. Insert the other vacuum tubes into the solar water tank according to the fourth item.
8. After checking the vacuum tube, immediately apply cold water or wait until the sun goes down before applying water to avoid exploding the vacuum tube.
Of course, if the cold water hose has been connected, you can also insert the hose while filling the water, so you do not need dishwashing liquid. For initial installation, follow the method above.