The reasons why the gasoline generator stalls after ignition for a period of time are:
1. Sensor: Disconnect the oil sensor connection cable and the gasoline engine can start. the oil change sensor.
2. Ignition System Problems: Disconnect the spark plug to start and observe the condition of the spark. White and red sparks are normal; If there is no spark, replace the spark plug or igniter.
3. Fuel system problems: Check to see if water has entered the fuel. If water has entered, clean the carburetor with gasoline. Determine if the cylinder is full of fuel. Determine whether there is an oil leak in the oil supply pipeline, change the position of the shock absorber, and see if it can start.
4. Problems with the air distribution system: Disconnect the spark plug and press fePress the air filter hole with your fingers. If there is no compressed gas escaping after several revolutions of idling, it means that there is a problem with the power conversion system and gas distribution system.
If the gasoline generator does not start, is it related to too much oil?
The reason why the gasoline generator cannot start is: insufficient battery voltage or voltage that is too low; The starter provides sufficient speed and torque to start the engine; Mechanical failure, including spark plug or ignition coil failure, prevents the engine from firing normally. A gasoline generator is generally composed of a stator, rotor, end cover, bearing and other components. An engine is a machine that converts chemical energy into mechanical energy. The conversion process is actually a process ofwork cycle which consists of generating. kinetic energy by burning fuel in the cylinder to drive the engine. The reciprocating movement of the piston in the engine cylinder causes the connecting rod connected to the piston and the crank connected to the connecting rod to reciprocate in a circular motion around the center of the crankshaft. to produce power.
One million subsidies for the purchase of a car
What should I do if the gasoline generator cannot start?
1 Reasons for which the gasoline generator cannot start
1. Whether engine oil and generator gasoline are filled. Otherwise, the generator will not be able to turn on and start.
2. If the engine has not been started for a long time, engine oil will flow back into the oil pan. When the engine first starts, there is no engine oil lubrication and the cylinder pressure cannot. At this point, too much gasoline (cold oil) will notwill not be used. If it burns and smothers the candle (the candle is wet), remove the candle, wipe it clean and burn it with a lighter. for a moment and put it back in place, or simply replace it with a new spark plug. (These are generally the reasons. If you remember, it can be used on many cars)
3 If it is not used frequently, it will usually be difficult to start when used . The carburetor level will drop and the oil level inside the carburetor will drop. At this time, too much gasoline (cold oil) does not burn, block the oil hole, or directly replace it with one. new spark plug. This is because it is not commonly used, the carburetor oil level drops and the cylinder pressure reaches. Otherwise, use a lighter to burn it for a while and put it back.
First check whether the engine oil and gasoline are newly added. Otherwise,they have been added for over three months and the oil and gasoline need to be drained and replaced. Engine oil and gasoline are only valid for three months. Oil and gasoline used for more than three months have lost their viscosity and are useless.
Check whether the engine oil and generator gasoline are refilled. Otherwise, the generator will not be able to turn on and start.
If the above is achieved, check if the spark plug lights. Otherwise, remove the spark plug, dip some gasoline in it and install it to see if the generator ignites. ignition and starting.
Detailed information:
When using a gasoline generator, please note:
1) Theory guides practice. Only by fully mastering the basic principles and basic structure of small gasoline engines can we carry out fault analysis and treatment, especially forFor different types of oil engines, specific analysis of specific models is required;
2) When an error occurs. Only by carrying out comprehensive and scientific analysis and judgment based on the scene can we guarantee that the fault is handled accurately, and we cannot handle the problem based on imagination or guesswork. so-called past experience. Gasoline engines often have oil lines, circuits and other parts that fail at the same time, leading to more complex failure phenomena. Sometimes similar phenomena occur at different fault points, causing certain troubleshooting difficulties.
By connecting and analyzing fault phenomena observed on site, imagining different possible causes of the fault and analyzing and comparing them, the extent and location of the fault can be determined. Then from simple to complex, from'outside to inside, first analyze the circuit then the oil circuit, then calibrate the ignition time, check the gas distribution order, and compress the fault to a certain point
3) Develop good habits, carry out necessary inspections before starting the machine, and regularly inspect the machine during operation to try to avoid sudden breakdowns
4) Strictly carry out technical maintenance at all levels; oil machine to ensure that the oil The machine is in good working condition to avoid sudden breakdowns and major accidents
Reference link: Baidu Encyclopedia_Gasoline Generator